Panasonic AJ-HPM200 Operating Instructions - Page 199
The following warning messages appear when an incorrect operation is attempted in the thumbnail playlist screen.
![]() |
View all Panasonic AJ-HPM200 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 199 highlights
Display No Character code Description Deck operation Appears when active frame data cannot be detected in the user bits in the HD SDI input Recording is during EE or recording. Normal recording will not be possible under these conditions. disabled *6 97 NO ACTIVE FRAME Check signal input to the unit. The input signal must contain the active frame data from a Operation variable frame-rate camera. (Appears when 29.97, 59-23, 60-24 or 60-25 is set in setup continues during menu No. 25 (SYSTEM FREQ) and setup menu No 040 (VFR REC) is set to ON.) recording Appears when active frame data detected from the user bit in the HD SDI input during EE Operation INVALID FRAME and recording exceeds 50p. Normal recording is not possible under these conditions. continues 98 RATE When SYSTEM FREQ is set to 60-25, set the frame rate on a variable frame-rate camera to 50p or less. Appears when SYSTEM FREQ is set to 60-25 and VFR REC is set to ON. ◆ NOTE: *6: An attempt to start recording causes the button to temporarily light. It goes out a few seconds later and no recording is made. For Long and Trouble-Free Operation The following warning messages appear when an incorrect operation is attempted in the thumbnail playlist screen. Item Thumbnail Message Description Measure CANNOT ACCESS Cannot access gateway server. GATEWAY! CHECK LAN SETTING Check if LAN setup is correct. CANNOT ACCESS! Data cannot be accessed because it is corrupted or for other reasons. Restore media and clips to normal state before access. When displayed during network operation, check LAN setup, make sure the LAN cable is correctly connected and check that your network environment is functioning properly. CANNOT ADD! NO User name or password in not entered correctly. Enter user name or password correctly. INPUT CANNOT CHANGE! A thumbnail containing a grayed out text memo that Edit settings or content to enable thumbnail display. cannot be generated is not available for editing. CANNOT CONNECT! Connection to the network cannot be established. Check LAN setup, make sure the LAN cable is correctly connected and check that your network environment is functioning properly. CANNOT DELETE! Contents version mismatch prevents deletion. Match devices and contents version. CANNOT FIND FTP-SERVER! FTP server cannot be found. Check if FTP client URL is correct. CANNOT FORMAT! P2 card problem prevents formatting. Check P2 card. CANNOT RE-CONNECT! A clip that does not span multiple cannot be reconnected. Check selected content. CANNOT REPAIR IN Some of the selected clip could not be repaired. SELECTION! CANNOT REPAIR! Selected content cannot be repaired. Check selected content. CANNOT SAVE! A network setup file with the same file name FILE NAME IN USE exists on the SD memory card. Save to a different name. CARD FULL! The P2 or SD memory card is full. Insert media with sufficient capacity. INVALID VALUE! Entered data was invalid. Enter data in a valid range. IP ADDRESS IS USED! The set IP address is used on another device. Consult the network administrator, and set another IP address. LACK OF REC CAPACITY! There is not enough recording capacity left on the Insert a card with sufficient recording capacity. card. LOGIN FAILED! Login to destination FTP server failed. Check if user ID and password for the FTP client are correct. MISSING CLIP! All cards that contain the clip must be inserted to Insert all cards that contain the clip. allow attachment of shot marks. NO CARD! No P2 or SD memory card is inserted. Insert compatible media. NO CONTENTS! No P2 data in the connected network folder. Connect to a folder that contains P2 data. NO COPY TO SAME A clip cannot be copied to the card storing the Copy the selected clip to a card that does not CARD! original clip. contain the original clip. NO INPUT! No data is input. Set after making input. For Long and Trouble-Free Operation: Error Messages 199
![](/manual_guide/products/panasonic-ajhpm200-operating-instructions-82ccd3e/199.png)