Panasonic AJ-HPM200 Operating Instructions - Page 198

Display No Character code Description Deck operation Displayed when the audio data of a signal input from the 1394 interface is irregular. 17 INVALID AUDIO SIG Operation continues *1 Displayed when the time code data of a signal input from the 1394 interface is irregular. Operation 18 INVALID TC SIG continues *2 Displayed when a video or audio error occurs during recording. 21 REC WARNING To continue operation, turn the power off and then back on again. STOP Displayed when data was corrupted due to a P2 card error during recording. STOP This error is displayed after recording ends and remains on until the start of the next CARD 26 operation. This error is not displayed during playback. (* indicates the slot number where ERROR the error occurred.) Replace the P2 card in the slot where the error occurred. Displayed when a LAN connection or disconnection failed. Power off, then power up STOP 49 LAN ERROR again before use. Should E-49 appear again, consult your supplier. Displayed when a drop in the backup battery voltage for the internal clock is detected at Operation 50 BATTERY EMPTY power on. Replace the internal battery. *5 continues DIR NG The P2 card directory structure is not supported. (* indicates the slot number where the Operation 70 CARD error occurred.) Make a quick backup of card data and format the card. continues RUNDOWN The maximum number of overwrites has been exceeded. (* indicates the slot number Operation 71 CARD where the error occurred.) This P2 card should be replaced. continues *3 Displayed for 3 seconds when a dropout due to reduced hard disk performance occurs Operation 75 HDD INTERMITTENT during hard disk playback for monitoring purposes. continues Use a faster hard disk. Displayed when a signal input from the 1394 interface is not a DVCPRO HD (100 Mbps) Recording is 90 NOT 1× 100M SIG 1× normal speed transfer signal. disabled Displayed when DV format recording is available and the copy guard signal input via the Recording is 91 COPY PROTECTED 1394 interface is in the copy inhibit mode. disabled 92 1394 INITIAL ERROR Displayed when the 1394 interface connection is irregular. *4 23.98Hz 24Hz 59-23Hz 60-24Hz 60-25Hz only Operation Appears during playback when the time code has been recorded in drop frame mode. continues The video output is distorted and audio output is muted at the drop point of the time code. Check the playback clip. Playing back a 24p frame-rate clip requires that the time code 93 INVALID TC MODE be recorded in non-drop frame mode. Appears when the time code in an HD SDI input is in the drop frame mode during EE or recording. Normal recording will not be possible under these conditions. Check signal input to the unit. Set the input time code to non-drop frame mode. (Appears when 23.98, 24, 59-23, 60-24 or 60-25 is set in setup menu No. 25 (SYSTEM FREQ).) Displayed while synchronizing recorded video frames to the time code of a signal input Operation INVALID EMBEDDED to the HD SDI connector when that time code is not advancing at 1× normal speed. (When continues 95 TC "SLTC" is selected in setup menu No. 032 (REC REF) or 29.97, 59-23, 60-24, 25 or 60-25 is selected in setup menu No. 25 (SYSTEM FREQ).) Appears during playback when frame rate data in user bit cannot be detected or when Operation the playback time code is not continuous. The video output is distorted and audio output continues is muted in sections where the time code is not continuous. Check the playback clip. INVALID TC Appears during EE or recording when frame rate data cannot be detected in the user bit 96 SEQUENCE data in an HD SDI input or when the input time code is not continuous. Normal recording will not be possible under these conditions. Check signal input to the unit. Input signals with a matching time code and pull-down sequence (Appears when 23.98, 24, 59-23, 60- 24 or 60-25 is set in setup menu No. 25 (SYSTEM FREQ).) ◆ NOTE: *1: This warning appears only during recording. Then the audio is recorded mute. *2: This warning appears only during recording. The internally generated time code is recorded. *3: Operation continues but normal recording or playback may not be possible. *4: This warning appears at any time. This error disables input to the digital video interface. *5: "E-50" appears when the backup battery is depleted. Consult your supplier for information on a store that can provide you with a new battery (CR2032 or the equivalent). Be sure to use setup menu No. 069 (CLOCK SET) to set the clock after battery replacement. 198 For Long and Trouble-Free Operation: Error Messages