Panasonic AJ-HPM200 Operating Instructions - Page 106
Changing Audio Level in an Event during Event Registration, Setting Audio Levels for Specific s
View all Panasonic AJ-HPM200 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 106 highlights
Changing Audio Level in an Event during Event Registration When registering a new event in a playlist, change the audio level during the registration of the event. 5 3 2,4 PLAYER STOP PREVIEW REC A.LEVEL REC SOURCE SELECT COUNTER STILL/ PLAY PAUSE REW FF RESET NEW TC PRESET PROP T TCG REGEN RESET EXT TO UB DE REVIEW 1 CLIP PLAY PREV NEXT UT CLIP F3 SHIFT PF4 CONTROL REMOTE LOCAL MODE 3 1 3 1 UNITY 4 2 4 2 UNITY 10 0 10 20 30 ʿ CH CH 1/3 2/4 PB 4 1 Assign IN and OUT points to enable event registration. 2 Use the UNITY/VAR channel selection switch to select tracks for level setting. • This method for setting the audio level is not available when the player is a hard disk or an external device. When an event has been captured to a P2 card, set the audio level. • Repeating previewing clears the level setting for the preview section where track selection is available at the start of each preview. • When a preview is interrupted during the preroll section, the level setting is not made and the previous level setting is not cleared. • Pressing the STOP button to interrupt preview makes settings valid until stopping. Audio level after the interruption point in the event is set to the same level as the interruption point. Setting Audio Levels for Specific Sections Use the following steps to change the audio level for specific sections in a playlist. 1 4 PLAYER STOP PREVIEW REC A.LEVEL REC SOURCE SELECT COUNTER STILL/ PLAY PAUSE REW FF RESET NEW TC PRESET CH 3 CH 4 PROP TEXT MEMO INT REGEN TCG PRESET MARKER EXT VIDEO A1 A2 GO TO EDIT MODE A3 A4 A.DUB LAST X TRIM MODE DELETE SLOT SELECT IN ENTRY OUT REVIEW 1 CLIP PLAY PREV NEXT SLOT CLIP PF1 CLIP LIST PF2 ALL CLIP PF3 SHIFT PF4 CONTROL REMOTE LOCAL MODE 3 1 3 1 UNITY 4 2 4 2 UNITY 10 0 10 20 30 ʿ CH CH 1/3 2/4 PB 3 Press the PREVIEW button to register the event. During preview, the audio is output according to the set level. 4 Use the UNITY/VAR channel selection switch of the audio fader and fader control during preview playback to change the level. After ending or interrupting a preview, the audio level set so far is reflected and an icon indicating that a level setting has been made appears on the event on the timeline. 5 Check audio level by performing a review or playlist playback. ◆ NOTE: • If the level setting value for all sections in an event is UNITY, the icon indicating that an event level setting has been made does not appear. • If a level setting for an entire playlist has been made for an extended period of time, a level setting cannot be added and an error is displayed. • A level setting for the preroll and postroll playback section cannot be changed. 36 5 1 Press the PLAYER button to switch to recorder operations. 2 Set the IN point at the location where you want to start setting the audio level of the recorder and set the OUT point where you want it to end. ➝Refer to "Setting IN and OUT points" (page 91). 3 Select the track where the audio level will be set. Select using the A1/A2/A3 (SHIFT + A1)/A4 (SHIFT + A2) buttons. 4 Press the A LEVEL REC (SHIFT + PREVIEW) button to start audio level recording/playback. Playback starts at the beginning of the preroll time section before the set IN point and stops 1 second later. During playback of audio level recording, the recorder screen displays "A LEVEL REC". 106 Editing: Setting Audio Level