Brother International Innov-is XJ1 Operation Manual - Page 191
than the Utility Stitch or Character/Decorative Stitch.
View all Brother International Innov-is XJ1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 191 highlights
ERROR MESSAGES Error messages Cause/solution The bobbin thread is almost empty. 36 This message is displayed when the bobbin thread is running out. Although a few stitches can be sewn when the "Start/Stop" button is pressed, replace with a wound bobbin immediately. When embroidering, press , press , remove the embroidery frame, and then replace the bobbin with one wound with plenty of embroidery bobbin thread. If [Upper and Bobbin Thread Sensor] in the general settings screen of the machine setting mode is set to [OFF], this message does not appear. 37 The bobbin winder safety device has activated. Is the thread tangled? This message is displayed when the bobbin is being wound, and the motor locks because the thread is tangled, etc. 38 The carriage of the embroidery unit will move. Keep This message is displayed when the embroidery unit is initializing. your hands etc. away from the carriage. The safety device was activated since the main 39 shaft motor was heated. Is the thread tangled? This message is displayed when the temperature of the motor increases, activating the safety device. Wait until the temperature decreases. If the error persists, contact your nearest authorized Brother dealer. 40 The safety device was activated since the main shaft motor seized. Is the thread tangled? This message is displayed when the motor locks due to tangled thread or for other reasons related to thread delivery. The safety device was activated since the needle 41 position sensor malfunctioned. This message is displayed when an error in the needle position sensor is detected, activating the safety device. Turn the machine off, then on again. If the message continues to appear, the machine may be damaged. Contact your nearest authorized Brother dealer. 42 The upper thread may not be threaded correctly. Thread the upper thread from the beginning. This message is displayed when it seems that the upper thread has not been threaded correctly. 43 The USB media was changed. Do not change the USB media while it is being read. This message is displayed when you attempt to select a stitch pattern after the USB media in which the stitch pattern is saved has been changed. 44 There is no needle plate cover. Attach a needle plate cover. This message is displayed when the needle plate cover is not attached. This editing function cannot be used when the 45 pattern is out of the red outline. Use this function after moving the pattern. This message is displayed when the machine is in embroidery edit mode, and you try to use an editing function when the pattern is not completely within the red outline. 46 This file cannot be used. This message appears if the file format is incompatible with this machine. Check the list of compatible file formats. (page 192) This file exceeds the data capacity and cannot be 47 used. Use a suitable size file. This message is displayed when the file size exceeds the data capacity of the machine. Confirm the file size and format. (page 192) This key cannot be used at this time. 48 This message is displayed when you press other than the Utility Stitch, or press than the Utility Stitch or Character/Decorative Stitch. in the screen in the screen other 49 This key does not operate when the needle is down. This message is displayed when a key on the LCD display is touched while Raise the needle and press the key again. the needle is in the down position. 50 This stitch is not "Dual Feed Mode" compatible. This message appears when the dual feed foot cannot be used with the current stitch. Select other stitch. 51 This USB media cannot be used. This message is displayed when you try to use incompatible media. 52 This USB media is incompatible. This message is displayed when you try to use incompatible USB media. For a list of compatible USB media, visit " http://s.brother/cpeaa/ ". 53 Turn off the machine before attaching or removing the needle plate. This message is displayed when the regular needle plate is replaced with the straight stitch needle plate while the machine is ON. Turn off the power and replace the needle plate. 54 • This message is displayed when the machine is set to embroidery mode or utility decorative stitch mode from the home page screen while the straight stitch needle plate or no needle plate is installed. • This message is displayed when the straight stitch needle plate is installed while a stitch pattern that cannot be used with that needle plate is selected. 55 USB media error This message is displayed when an error occurs with the USB media. Appendix 7 189