Home » Canon Manuals » Video Cameras » Canon EOS C300 Mark III » Manual Viewer

Canon EOS C300 Mark III EOS C300 Mark III EOS C500 Mark II Instruction Manual - Page 104

Setting the Audio Input Type for the INPUT 1/INPUT 2 Terminals

View all Canon EOS C300 Mark III manuals

Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Recording Audio 104 Setting the Audio Input Type for the INPUT 1/INPUT 2 Terminals Using the INPUT 1/INPUT 2 terminals, you can record audio independently from a microphone or audio input source. Set the INPUT 1 or INPUT 2 switch to AES/EBU (digital audio), LINE (analog audio device) or MIC (analog microphone). • When a terminal's INPUT (audio source selection) switch is set to AES/EBU, the audio recording level for that input cannot be adjusted. • When using the INPUT terminals to record to only one channel, use the INPUT 1 terminal. INPUT 1 / INPUT 2 switches (audio source selection) IMPORTANT • Using an analog microphone that requires phantom power - Be sure to connect/disconnect the microphone with the camera turned off or when the respective INPUT switch is set to the MIC position. Only after the microphone is connected, set the switch to MIC+48V. - The same applies also to INPUT terminals on an optional EU-V2 Expansion Unit 2 attached to the camera. • To connect a microphone or other audio device that is not compatible with phantom power to an INPUT terminal, make sure the respective INPUT (audio source selection) switch is set to a position that matches the device (AES/EBU, LINE or MIC). Setting the switch to MIC+48V may damage the audio device. Selecting the Audio Input Source for Audio Channels In CAMERA mode, you can select the audio input source that will be recorded on CH1/CH2 or CH3/CH4, independently for each pair of audio channels. For details refer to the Audio Settings and Recorded Audio Channels table (A 100). 1 Select > [¡ Audio Setup] > [Audio Input Selection] > [CH1/CH2] or [CH3/CH4]. 2 Select [INPUT Terminals] (external microphone or audio device), [MIC Terminal] (external microphone) or [Monaural Mic] (built-in microphone). • When an optional EU-V2 Expansion Unit 2 with a commercially available V-mount battery is attached to the camera, the [INPUT Terminals] option changes to [INPUT Terminals (Camera)] and you have an additional option [INPUT Terminals (Exp. Unit)] (only for [CH3/CH4]) to record audio from the INPUT terminals on the EU-V2. About the monaural microphone The monaural microphone allows you to add comments while shooting, which can be synchronized to the audio and video during editing. The audio recording level of the monaural microphone is adjusted automatically and cannot be changed. Monaural microphone

Section	Page
Safety Instructions	2
Table of Contents	5
1. Introduction	9
About this Manual	9
Conventions Used in this Manual	9
Supplied Accessories	10
Before Using the Camera	11
Names of Parts	12
Camera	12
LM-V2 LCD Monitor	18
LA-V2 LCD Attachment Unit	19
GR-V1 Camera Grip	20
Handle Unit	21
4K and Higher Resolutions: Workflow Overview	22
Color Grading with the ACES Workflow	23
2. Preparations	25
Preparing the Power Supply	25
Using a Battery Pack	25
Using the DC IN 12V Terminal	27
Preparing the Handle Unit and LCD Monitor	29
Attaching the Handle Unit	29
Attaching the LCD Monitor	29
Adjusting the LCD Monitor	31
Removing the LCD Monitor and LCD Attachment Unit	32
Date, Time and Language Settings	33
Setting the Date and Time	33
Changing the Language	33
Using the Menus	34
Selecting an Option from the Menu	34
Using the Customized Menus (My Menu)	35
Preparing the Lens	37
Attaching an EF Lens	37
Updating the Firmware of an EF Lens	38
In-Camera Lens Correction	39
Preparing Other Accessories	40
Examples of Camera Configurations	40
Removing and Attaching the Camera Grip	41
Attaching the Microphone Holder	42
Preparing Recording Media	43
Compatible Recording Media	43
Inserting a CFexpress Card	44
Removing a CFexpress Card	44
Inserting and Removing an SD Card	45
Initializing Recording Media	46
Switching Between CFexpress Card Slots	46
Relay Recording and Double Slot Recording	47
Checking the Remaining Recording Time on a Card	47
Recovering Clips	48
Adjusting the Black Balance	49
3. Recording	51
Recording Video and Photos	51
Recording	51
Onscreen Displays	53
Selecting the Onscreen Display Level	57
Setting a Card’s Volume Label	59
Setting the Clip File Name	59
Using the Fan	61
Video Configuration: Video Format, Sensor Mode, System Frequency, Resolution and Frame Rate	62
Selecting the Sensor Mode	62
Selecting the Main Recording Format	62
Selecting the System Frequency	62
Selecting the Resolution and Color Sampling Settings	62
Selecting the Frame Rate	63
Selecting the Bit Rate	63
Proxy Clips (Simultaneous Recording)	66
Direct Setting Mode (FUNC Button)	67
Using the Direct Setting Mode	67
Shutter Speed	68
Changing the Shutter Speed Mode and Value	69
ISO Speed/Gain	70
Changing the ISO Speed or Gain Value	71
Using the Control Dial	71
ND Filter	72
Aperture	73
Manual Aperture: Changing the Aperture Value	73
Using the Control Dial	74
Momentary Automatic Aperture - Push Auto Iris	75
Automatic Aperture	75
Exposure Compensation - AE Shift	76
Light Metering Mode	76
White Balance	77
Custom White Balance	77
Color Temperature/Preset White Balance	78
Auto White Balance (AWB)	79
Focus	80
Manual Focus	81
Using the Focus Assistance Functions	82
One-Shot AF	84
AF-Boosted MF	84
Continuous AF	85
Changing the AF Frame Size and Position	86
Face Detection	87
Tracking a Specific Subject	88
Image Stabilization	89
Zoom	90
Onscreen Markers, Zebra Patterns and False Color	91
Displaying Onscreen Markers	91
Displaying Zebra Patterns	93
Displaying False Color	93
Setting the Time Code	94
Selecting the Time Code Mode	94
Selecting Drop or Non-Drop Frame	95
Setting the User Bit	96
Synchronizing with an External Device	97
Connecting an External Device	97
Time Code Signal Input	97
Time Code Signal Output	98
Reference Video Signal Input (Genlock Synchronization)	98
Reference Video Signal Output	99
Recording Audio	100
Audio Settings and Recorded Audio Channels	100
Connecting an External Microphone or External Audio Input Source to the Camera	103
Setting the Audio Input Type for the INPUT 1/INPUT 2 Terminals	104
Selecting the Audio Input Source for Audio Channels	104
Adjusting the Audio Recording Level	105
Advanced Audio Input Settings	106
Monitoring the Audio with Headphones	107
Colors Bars/Audio Reference Signal	108
Color Bars	108
Audio Reference Signal	108
Video Scopes	109
Displaying a Video Scope	109
Configuring the Waveform Monitor	109
Configuring the Vectorscope	110
Adding Marks to Clips in CAMERA Mode	111
Adding a Shot Mark while Recording	111
Adding an OK Mark or Check Mark to the Last Clip Recorded	111
Using Metadata	112
Setting a User Memo Created with Canon XF Utility	112
Entering Slate Information About the Recording	113
Reviewing a Recording	114
Special Recording Modes	115
Slow & Fast Motion Recording	115
Pre-recording	118
Using Anamorphic Lenses	119
Using the Optional RC-V100 Remote Controller	120
4. Customization	121
Assignable Buttons	121
Assignable functions	122
Custom Picture Settings	125
Selecting Custom Picture Files	125
Preset Picture Settings	125
Renaming Custom Picture Files	126
Protecting Custom Picture Files	126
Resetting Custom Picture Files	126
Editing a Custom Picture File’s Settings	127
Copying Custom Picture Files	127
Embedding the Custom Picture File in Clips	127
Available Custom Picture Settings	128
Saving and Loading Menu Settings	132
Saving Menu Settings	132
Loading Menu Settings	132
5. Playback	133
Playback	133
Clip Index Screen	133
Switching Index Screens	134
Playing Back Recordings	135
Onscreen Displays During Clip Playback	136
Clip Playback Controls	137
Adjusting the Volume	137
Clip/Photo Operations	138
Clip/Photo Menu Operations	138
Displaying Clip Information	139
Adding OK Marks or Check Marks	140
Deleting OK Marks or Check Marks	140
Adding Shot Marks	140
Deleting All the Shot Marks from a Clip	141
Deleting Clips and Photos	141
Deleting the User Memo and GPS Information from a Clip	141
6. External Connections	143
Video Output Configuration	143
SDI OUT Terminal Video Output Configuration (Recording/Playback)	143
MON. Terminal / HDMI OUT Terminal Video Output Configuration (Recording/Playback)	144
Connecting to an External Monitor or Recorder	145
Using the SDI OUT Terminal	145
Using the MON. Terminal	146
Using the HDMI OUT Terminal	146
Selecting the Video Output’s Scan Mode	147
Superimposing Onscreen Displays on Video Outputs	147
Changing the Opacity Level of Onscreen Displays	147
Selecting the Output Range	148
Applying a LUT to Video Outputs	149
Adjusting the Color Quality for HLG Output	150
Adjusting the Gain Difference between HDR and SDR	150
User LUTs	151
Audio Output	153
Working with Clips on a Computer	154
Saving XF-AVC Clips	154
Developing RAW Clips	154
7. Network Functions	155
About the Network Functions	155
Using Networks	156
Using a Wi-Fi Network	156
Using a Wired (Ethernet) Network	157
Configuring Connection Settings	158
Adding a New Connection Setting Using the Wizard	159
Function Settings	160
Other Connection Methods	163
Checking and Changing Connection Settings	165
Configuring the Camera’s IP Address Manually	167
Checking and Changing Communication Settings/Function Settings	167
Configuring IPv6 Settings	169
Reading a Root Certificate for FTPS Transfer	169
802.1X Authentication	170
Giving a Nickname to the Camera	170
Checking the Network’s Status	171
FTP File Transfer	172
Transferring a Single Clip	172
Transferring All Clips	172
IP Streaming	173
Browser Remote: Controlling the Camera from a Network Device	175
Starting Browser Remote	175
Using Browser Remote	177
8. Additional Information	183
Menu Options	183
Displaying the Status Screens	196
Troubleshooting	206
List of Messages	212
Handling Precautions	217
Maintenance/Others	220
Optional Accessories	221
Specifications	223
Camera	223
Accessories	226
Reference Tables	228
Approximate Recording Time on a Card	228
Charging Times	228
Approximate Usage Times with a Fully Charged Battery Pack	229
Appendix: Compatible Lenses and Functions	230
Appendix: Camera Dimensions	233

Match case Limit results 1 per page

Recording Audio

104

Setting the Audio Input Type for the INPUT 1/INPUT 2 Terminals

Using the INPUT 1/INPUT 2 terminals, you can record audio independently from a microphone or audio input

source.

Set the INPUT 1 or INPUT 2 switch to AES/EBU (digital audio),

LINE (analog audio device) or MIC (analog microphone).

•

When a terminal’s INPUT (audio source selection) switch is set to

AES/EBU, the audio recording level for that input cannot be

adjusted.

•

When using the INPUT terminals to record to only one channel,

use the INPUT 1 terminal.

IMPORTANT

•

Using an analog microphone that requires phantom power

Be sure to connect/disconnect the microphone with the camera

turned off or when the respective INPUT switch is set to the MIC

position. Only after the microphone is connected, set the switch to MIC+48V.

The same applies also to INPUT terminals on an optional EU-V2 Expansion Unit 2 attached to the camera.

•

To connect a microphone or other audio device that is not compatible with phantom power to an INPUT

terminal, make sure the respective INPUT (audio source selection) switch is set to a position that matches the

device (AES/EBU, LINE or MIC). Setting the switch to MIC+48V may damage the audio device.

Selecting the Audio Input Source for Audio Channels

In CAMERA mode, you can select the audio input source that will be recorded on CH1/CH2 or CH3/CH4,

independently for each pair of audio channels. For details refer to the

Audio Settings and Recorded Audio

Channels

table (

100).

1 Select

> [

Audio Setup] > [Audio Input Selection] > [CH1/CH2] or [CH3/CH4].

2 Select [INPUT Terminals] (external microphone or audio device), [MIC Terminal] (external

microphone) or [Monaural Mic] (built-in microphone).

•

When an optional EU-V2 Expansion Unit 2 with a commercially available V-mount battery is attached to the

camera, the [INPUT Terminals] option changes to [INPUT Terminals (Camera)] and you have an additional

option [INPUT Terminals (Exp. Unit)] (only for [CH3/CH4]) to record audio from the INPUT terminals on the

EU-V2.

About the monaural microphone

The monaural microphone allows you to add comments while shooting,

which can be synchronized to the audio and video during editing. The audio

recording level of the monaural microphone is adjusted automatically and

cannot be changed.

INPUT 1 / INPUT 2 switches

(audio source selection)

Monaural

microphone