Cisco SGE2000 Configuration Guide - Page 118

Rebooting and Shutting Down the SCE Platform, Rebooting the SCE Platform - serial port settings

Get Cisco SGE2000 PDF manuals and user guides View all Cisco SGE2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Rebooting and Shutting Down the SCE Platform Chapter 7 Basic SCE 2000 Platform Operations Rebooting and Shutting Down the SCE Platform • Rebooting the SCE Platform • How to Shut Down the SCE Platform Rebooting the SCE Platform Rebooting the SCE platform is required after installing a new firmware, in order for that firmware to take effect. There might be other occasions where rebooting the SCE platform is necessary. Note When the SCE restarts, it loads the startup configuration, so all changes made in the running configuration will be lost. You are advised to save the running configuration before performing reload, as described in How to Save or Change the Configuration Settings. SUMMARY STEPS 1. At the SCE 2000# prompt, type reloadand press Enter. 2. Type y to confirm the reboot request and press Enter. DETAILED STEPS Step 1 Step 2 At the SCE 2000# prompt, type reloadand press Enter. A confirmation message appears. Type y to confirm the reboot request and press Enter. Examples for Rebooting the SCE Platform The following example shows the commands for system reboot. SCE 2000# reloadAre you sure? ythe system is about to reboot, this will end your CLI session How to Shut Down the SCE Platform Shutting down the SCE platform is required before turning the power off. This helps to ensure that non-volatile memory devices in the SCE platform are properly flushed in an orderly manner. Note When the SCE platform restarts, it loads the startup configuration, so all changes made in the running configuration will be lost. You are advised to save the running configuration before performing reload, as described in How to Save or Change the Configuration Settings. SUMMARY STEPS 1. Connect to the serial console port (The CON connector on the SCE platform front panel, 9600 baud). 7-10 Cisco SCE 2000 4xGBE Installation and Configuration Guide OL-7824-06

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
7-10
Cisco SCE 2000 4xGBE Installation and Configuration Guide
OL-7824-06
Chapter 7
Basic SCE 2000 Platform Operations
Rebooting and Shutting Down the SCE Platform
Rebooting and Shutting Down the SCE Platform
•
Rebooting the SCE Platform
•
How to Shut Down the SCE Platform
Rebooting the SCE Platform
Rebooting the SCE platform is required after installing a new firmware, in order for that firmware to take
effect. There might be other occasions where rebooting the SCE platform is necessary.
Note
When the SCE restarts, it loads the startup configuration, so all changes made in the running
configuration will be lost. You are advised to save the running configuration before performing reload,
as described in
How to Save or Change the Configuration Settings
.
SUMMARY STEPS
1.
At the SCE 2000# prompt, type
reload
and press Enter.
2.
Type
y
to confirm the reboot request and press Enter.
DETAILED STEPS
Step 1
At the SCE 2000# prompt, type
reload
and press Enter.
A confirmation message appears.
Step 2
Type
y
to confirm the reboot request and press Enter.
Examples for Rebooting the SCE Platform
The following example shows the commands for system reboot.
SCE 2000#
reload
Are you sure?
y
the system is about to reboot, this will end your CLI
session
How to Shut Down the SCE Platform
Shutting down the SCE platform is required before turning the power off. This helps to ensure that
non-volatile memory devices in the SCE platform are properly flushed in an orderly manner.
Note
When the SCE platform restarts, it loads the startup configuration, so all changes made in the running
configuration will be lost. You are advised to save the running configuration before performing reload,
as described in
How to Save or Change the Configuration Settings
.
SUMMARY STEPS
1.
Connect to the serial console port (The CON connector on the SCE platform front panel, 9600 baud).