Cisco SGE2000 Configuration Guide - Page 99

How to Con the GBE Interface Parameters, How to Cable the GBE Line Interface Ports

Get Cisco SGE2000 PDF manuals and user guides View all Cisco SGE2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

Chapter 6 Cabling the Line Ports and Completing the Installation Connecting the line ports to the network How to Configure the GBE Interface Parameters By default, the SCE 2000 GBE line interface ports are configured with auto-negotiation disabled. The procedure for enabling auto-negotiation for the GBE line interface ports is explained in the following section. Note Auto-negotiation must be disabled when the SCE 2000 is deployed via an external optical splitter (receive-only topology) Note If you change any parameters, you must save the new configuration settings. Type copy running-config startup-config , and press Enter. Note The maximum packet size supported by the SCE platform is 1600 bytes SUMMARY STEPS 1. To enter the Global Configuration Mode, at the SCE 2000# prompt, type configure, and press Enter. 2. To enter the desired GBE port interface, type interfaceGigabitEthernet 0/ portnumber, and press Enter, where portnumberis the number of the selected port (1-4). 3. Type auto-negotiateand press Enter. 4. To return to Global Configuration Mode, type exitand press Enter. DETAILED STEPS Step 1 Step 2 Step 3 Step 4 To enter the Global Configuration Mode, at the SCE 2000# prompt, type configure, and press Enter. The SCE 2000(config)# prompt appears. To enter the desired GBE port interface, type interfaceGigabitEthernet 0/ portnumber, and press Enter, where portnumberis the number of the selected port (1-4). The SCE 2000(config if)# prompt appears. Type auto-negotiateand press Enter. The SCE 2000(config if)# prompt appears. To return to Global Configuration Mode, type exitand press Enter. The SCE 2000(config)# prompt appears. Repeat this procedure to configure auto-negotiation for the other GBE port interfaces as needed. How to Cable the GBE Line Interface Ports The following sections present the general procedure for cabling the GBE interface ports. Refer to Cabling Diagrams to find the appropriate cabling diagram for the topology of your system for the specific connections required. OL-7824-06 Cisco SCE 2000 4xGBE Installation and Configuration Guide 6-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
6-7
Cisco SCE 2000 4xGBE Installation and Configuration Guide
OL-7824-06
Chapter 6
Cabling the Line Ports and Completing the Installation
Connecting the line ports to the network
How to Configure the GBE Interface Parameters
By default, the
SCE 2000
GBE line interface ports are configured with auto-negotiation disabled. The
procedure for enabling auto-negotiation for the GBE line interface ports is explained in the following
section.
Note
Auto-negotiation must be disabled when the
SCE 2000
is deployed via an external optical splitter
(receive-only topology)
Note
If you change any parameters, you must save the new configuration settings. Type
copy running-config
startup-config
, and press Enter.
Note
The maximum packet size supported by the SCE platform is 1600 bytes
SUMMARY STEPS
1.
To enter the Global Configuration Mode, at the SCE 2000# prompt, type
configure
, and press Enter.
2.
To enter the desired GBE port interface, type
interfaceGigabitEthernet 0
/
portnumber
, and press
Enter, where
portnumber
is the number of the selected port (1-4).
3.
Type
auto-negotiate
and press Enter.
4.
To return to Global Configuration Mode, type
exit
and press Enter.
DETAILED STEPS
Step 1
To enter the Global Configuration Mode, at the SCE 2000# prompt, type
configure
, and press Enter.
The SCE 2000(config)# prompt appears.
Step 2
To enter the desired GBE port interface, type
interfaceGigabitEthernet 0
/
portnumber
, and press Enter,
where
portnumber
is the number of the selected port (1-4).
The SCE 2000(config if)# prompt appears.
Step 3
Type
auto-negotiate
and press Enter.
The SCE 2000(config if)# prompt appears.
Step 4
To return to Global Configuration Mode, type
exit
and press Enter.
The SCE 2000(config)# prompt appears.
Repeat this procedure to configure auto-negotiation for the other GBE port interfaces as needed.
How to Cable the GBE Line Interface Ports
The following sections present the general procedure for cabling the GBE interface ports. Refer to
Cabling Diagrams
to find the appropriate cabling diagram for the topology of your system for the
specific connections required.