Cisco SGE2000 Configuration Guide - Page 69

Access Control List number, IP access ACL

Get Cisco SGE2000 PDF manuals and user guides View all Cisco SGE2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Chapter 5 Connecting the Management Interfaces and Performing Initial System Configuration Initial System Configuration Table 5-1 Setup Command Parameters Parameter Definition Access Control List number How many ACLs will be necessary? What IP addresses will be permitted/denied access for each management interface? You may want ACLs for the following: • Any IP access • Telnet access • SNMP GET access • SNMP SET access list entries (maximum 20 per list) IP address, and whether permitted or denied access. IP access ACL ID number of the ACL controlling IP access. telnet ACL ID number of the ACL controlling telnet access. SNMP Configuration SNMP agent status Enable or disable SNMP management. GET community names Community strings to allow GET access and associated ACLs (maximum 20). SET community names Community strings to allow SET access and associated ACLs (maximum 20). trap managers (maximum 20) Trap manager IP address, community string, and SNMP version. Authentication Failure trap status Sets the status of the Authentication Failure traps. enterprise traps status Sets the status of the enterprise traps. system administrator Name of the system administrator. Topology Configuration Connection mode Is the SCE 2000 installed using inline topology or receive-only topology using an optical splitter? type of deployment Is this a cascade topology, with two SCE 2000 s connected via the cascade ports? Or is this a single platform topology? physically connected link (cascade topology only) In a cascade deployment this parameter sets the index for the link that this SCE 2000 is deployed on. The options for SCE 2000 are link-0 or link-1. In a single- SCE 2000 Platform deployment this parameter is not relevant since one SCE 2000 is deployed on both links. In this case the link connected to port1-port2 is by default link-0 and the link connected to port3-port4 is be default link-1. priority (cascade topology only) If this is a cascaded topology, is this SCE 2000 the primary or secondary SCE 2000 ? OL-7824-06 Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
5-5
Cisco SCE 2000 4xGBE Installation and Configuration Guide
OL-7824-06
Chapter 5
Connecting the Management Interfaces and Performing Initial System Configuration
Initial System Configuration
Access Control List number
How many ACLs will be necessary? What IP
addresses will be permitted/denied access for each
management interface? You may want ACLs for
the following:
•
Any IP access
•
Telnet access
•
SNMP GET access
•
SNMP SET access
list entries (maximum 20 per list)
IP address, and whether permitted or denied
access.
IP access ACL
ID number of the ACL controlling IP access.
telnet ACL
ID number of the ACL controlling telnet access.
SNMP Configuration
SNMP agent status
Enable or disable SNMP management.
GET community names
Community strings to allow GET access and
associated ACLs (maximum 20).
SET community names
Community strings to allow SET access and
associated ACLs (maximum 20).
trap managers (maximum 20)
Trap manager IP address, community string, and
SNMP version.
Authentication Failure trap status
Sets the status of the Authentication Failure traps.
enterprise traps status
Sets the status of the enterprise traps.
system administrator
Name of the system administrator.
Topology Configuration
Connection mode
Is the
SCE 2000
installed using inline topology or
receive-only topology using an optical splitter?
type of deployment
Is this a cascade topology, with two
SCE 2000
s
connected via the cascade ports? Or is this a single
platform topology?
physically connected link (cascade topology only)
In a cascade deployment this parameter sets the
index for the link that this
SCE 2000
is deployed
on. The options for
SCE 2000
are link-0 or link-1.
In a single-
SCE 2000
Platform deployment this
parameter is not relevant since one
SCE 2000
is
deployed on both links. In this case the link
connected to port1-port2 is by default link-0 and
the link connected to port3-port4 is be default
link-1.
priority (cascade topology only)
If this is a cascaded topology, is this
SCE 2000
the
primary or secondary
SCE 2000
?
Table 5-1
Setup Command Parameters
Parameter
Definition