Cisco SGE2000 Configuration Guide - Page 79

Step 1, The Access Control Lists configuration dialog begins.

Get Cisco SGE2000 PDF manuals and user guides View all Cisco SGE2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Chapter 5 Connecting the Management Interfaces and Performing Initial System Configuration Initial System Configuration DETAILED STEPS Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Enter the Access Control Lists configuration menu. Would you like to enter the Access lists configuration menu? [no]: y Type y and press Enter. The Access Control Lists configuration dialog begins. You have the option of creating or modifying Access Control Lists, or skipping this section and proceeding directly to assign the existing ACLs to the desired management interfaces. Would you like to create new Access lists or modify existing lists? [no]: y If you choose not to create or edit Access Control Lists, skip to : Configuring the Topology-Dependent Parameters (on page 5-19). Type the number of the Access Control List to be configured (1 through 99) and press Enter. Note that there is no default for this parameter. Begin adding entries to the selected list. Indicate whether this entry is permitted access or denied access. • To permit access press Enter. • To deny access type nand press Enter. Does this entry permit access? [yes]: Type the IP address to be added to this list, and press Enter. Type "any" and press Enter to include any IP address in the ACL. Note that there is no default for this parameter. Enter IP address or the word 'any' to denote any IP address: If you entered a specific IP address, enter the wildcard bits to define a range of IP addresses and press Enter. (See Entry Formats (on page 5-13).) To define an individual IP address, type 0.0.0.0and press Enter. There is no default for this parameter. Enter wildcard bits: The maximum number of entries in an ACL is 20. If the "any" option was used, no other IP addresses may be added to the list. • To add more entries, type yand press • Enter Would you like to add another entry to this list? [no]:y Enter up to 20 entries as described in and . • When all entries have been added, press • Enter Would you like to add another entry to this list? [no]: When all entries are added to one list, you are asked whether you would like to create another ACL. You may define up to 99 ACLs. • To create another ACL, type y and press • Enter Would you like to configure another list? [no]: y Enter up to 20 IP addresses in this new ACL, as described in and . OL-7824-06 Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
5-15
Cisco SCE 2000 4xGBE Installation and Configuration Guide
OL-7824-06
Chapter 5
Connecting the Management Interfaces and Performing Initial System Configuration
Initial System Configuration
DETAILED STEPS
Step 1
Enter the Access Control Lists configuration menu.
Would you like to enter the Access lists configuration menu? [no]:
y
Type y and press Enter.
The Access Control Lists configuration dialog begins.
Step 2
You have the option of creating or modifying Access Control Lists, or skipping this section and
proceeding directly to assign the existing ACLs to the desired management interfaces.
Would you like to create new Access lists or modify existing lists? [no]:
y
If you choose not to create or edit Access Control Lists, skip to : Configuring the Topology-Dependent
Parameters (on page 5-19).
Step 3
Type the number of the Access Control List to be configured (1 through 99) and press Enter.
Note that there is no default for this parameter.
Step 4
Begin adding entries to the selected list.
Indicate whether this entry is permitted access or denied access.
•
To permit access press Enter.
•
To deny access type
n
and press Enter.
Does this entry permit access? [yes]:
Step 5
Type the IP address to be added to this list, and press Enter.
Type “any” and press Enter to include any IP address in the ACL.
Note that there is no default for this parameter.
Enter IP address or the word ‘
any
’ to denote any IP address:
Step 6
If you entered a specific IP address, enter the wildcard bits to define a range of IP addresses and press
Enter. (See Entry Formats (on page 5-13).)
To define an individual IP address, type
0.0.0.0
and press Enter.
There is no default for this parameter.
Enter wildcard bits:
Step 7
The maximum number of entries in an ACL is 20.
If the “any” option was used, no other IP addresses may be added to the list.
•
To add more entries, type
y
and press
•
Enter
Would you like to add another entry to this list? [no]:
y
Enter up to 20 entries as described in and .
•
When all entries have been added, press
•
Enter
Would you like to add another entry to this list? [no]:
Step 8
When all entries are added to one list, you are asked whether you would like to create another ACL. You
may define up to 99 ACLs.
•
To create another ACL, type y and press
•
Enter
Would you like to configure another list? [no]:
y
Enter up to 20 IP addresses in this new ACL, as described in and .