Cisco SGE2000 Configuration Guide - Page 87

Step 10: How to Complete and Save the Configuration

Get Cisco SGE2000 PDF manuals and user guides View all Cisco SGE2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

Chapter 5 Connecting the Management Interfaces and Performing Initial System Configuration Initial System Configuration In this case, the user must specify the physically-connected-link index (link-0 in our example), the priority of the SCE 2000 , and the on-failure link behavior. Would you like to enter the Topology configuration menu? [no]: yEnter Connection mode: 1- inline 2- receive-only Enter your choice [1]: 1Is this a cascade deployment ? [no]: yesEnter Physically connected link: 0- link-0 1- link-1 Enter your choice [0]: 0Enter SCE 2000 priority: 1- primary 2- secondary Enter your choice [1]: 2Enter On-failure behavior: 1- bypass 2- cutoff Enter your choice [1]: 1Enter admin status of the SCE after abnormal boot: 1- Operational 2- Not-Operational Enter your choice [1]: 1Data collection for the system configuration is completed. Step 10: How to Complete and Save the Configuration When you have completed the entire configuration, the system checks for errors. If errors are found, a warning message appears. When the configuration is error-free, you may apply and save it. SUMMARY STEPS 1. The system informs you that data collection is complete. 2. If any errors are detected, you may choose to view them. 3. You are asked whether to apply and save the configuration. 4. If there are no errors, the system requests confirmation of either a yes or no answer, in order to prevent mistakes. 5. If the configuration was applied and saved, you may also save it to a file at a remote station. 6. The system informs you that the configuration is complete. DETAILED STEPS Step 1 Step 2 The system informs you that data collection is complete. We recommend that you view the entire new configuration before it is applied. Type yand press Enter. Note that there is no default. If there are no errors, go to . Data collection for the system configuration is completed. Would you like to view the new configuration before it is applied? [yes/no]: y If any errors are detected, you may choose to view them. Press Enter. Found errors in the new configuration, would you like to view them? [yes]: The following errors were found: Warning - RDR formatter destination 10.1.1.1 is not allowed in the IP access-class. OL-7824-06 Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
5-23
Cisco SCE 2000 4xGBE Installation and Configuration Guide
OL-7824-06
Chapter 5
Connecting the Management Interfaces and Performing Initial System Configuration
Initial System Configuration
In this case, the user must specify the physically-connected-link index (link-0 in our example), the
priority of the
SCE 2000
, and the on-failure link behavior.
Would you like to enter the Topology configuration menu? [no]:
y
Enter Connection mode:
1- inline
2- receive-only
Enter your choice [1]:
1
Is this a cascade deployment ? [no]:
yes
Enter Physically connected
link:
0- link-0
1- link-1
Enter your choice [0]:
0
Enter SCE 2000 priority:
1- primary
2- secondary
Enter your choice [1]:
2
Enter On-failure behavior:
1- bypass
2- cutoff
Enter your choice [1]:
1
Enter admin status of the SCE after abnormal boot:
1- Operational
2- Not-Operational
Enter your choice [1]:
1
Data collection for the system configuration is completed.
Step 10: How to Complete and Save the Configuration
When you have completed the entire configuration, the system checks for errors. If errors are found, a
warning message appears. When the configuration is error-free, you may apply and save it.
SUMMARY STEPS
1.
The system informs you that data collection is complete.
2.
If any errors are detected, you may choose to view them.
3.
You are asked whether to apply and save the configuration.
4.
If there are no errors, the system requests confirmation of either a yes or no answer, in order to
prevent mistakes.
5.
If the configuration was applied and saved, you may also save it to a file at a remote station.
6.
The system informs you that the configuration is complete.
DETAILED STEPS
Step 1
The system informs you that data collection is complete.
We recommend that you view the entire new configuration before it is applied.
Type
y
and press Enter.
Note that there is no default.
If there are no errors, go to .
Data collection for the system configuration is completed.
Would you like to view the new configuration before it is applied? [yes/no]:
y
Step 2
If any errors are detected, you may choose to view them.
Press Enter.
Found errors in the new configuration, would you like to view them? [yes]:
The following errors were found:
Warning - RDR formatter destination 10.1.1.1 is not allowed in the IP access-class.