HP LH4r HP Netserver LP 1000r User Guide - Page 110

POST Error Messages

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Chapter 12 Troubleshooting 5. Replace the cover and connect all cables. 6. Turn on the monitor and Netserver. 7. If the Netserver still does not work: ◊ Repeat steps 1, 2, and 3 of this section. ◊ Remove all accessories, except the primary boot hard disk drive. ◊ Replace the cover and connect all cables. ◊ Turn on the monitor and the Netserver. ◊ If the Netserver now works, replace the boards and accessories one at a time to determine which one is causing the problem. 8. If the Netserver still does not work contact your service representative to replace the Netserver. POST Error Messages If you get a POST text error message in reverse video, press the [Enter] key (View System Error) to get a more detailed explanation and a possible solution. If the Netserver starts, but POST still reports an error message, clear the CMOS configuration, as described later in this chapter. NOTE HP recommends you correct the error before proceeding, even if the Netserver appears to start successfully. Table 12-1 describes the typical POST text error messages and the corrective action you may take to remedy the problem. 104

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 12
Troubleshooting
104
5.
Replace the cover and connect all cables.
6.
Turn on the monitor and Netserver.
7.
If the Netserver still does not work:
◊
Repeat steps 1, 2, and 3 of this section.
◊
Remove all accessories, except the primary boot hard disk drive.
◊
Replace the cover and connect all cables.
◊
Turn on the monitor and the Netserver.
◊
If the Netserver now works, replace the boards and accessories one at a
time to determine which one is causing the problem.
8.
If the Netserver still does not work contact your service representative to
replace the Netserver.
POST Error Messages
If you get a POST text error message in reverse video, press the [
Enter
] key
(View System Error) to get a more detailed explanation and a possible solution.
If the Netserver starts, but POST still reports an error message, clear the CMOS
configuration, as described later in this chapter.
NOTE
HP recommends you correct the error before proceeding, even
if the Netserver appears to start successfully.
Table 12-1 describes the typical POST text error messages and the corrective
action you may take to remedy the problem.