HP LH4r HP Netserver LP 1000r User Guide - Page 127

inside edge of the outer-rail assemblies. See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 127 highlights

Chapter 13 Alternative Rack Mounting (4-Post) 1. Lower the leveler screws on the rack's lower four corners to make firm contact with the floor. See Figure 13-4. 2. Ensure you have extended the anti-tip foot from the rack before continuing this procedure. See Figure 13-4. NOTE The HP Netserver weighs 32 lbs. (14.5 kg.) fully loaded. It is not necessary to use two people when placing the Netserver into the rack, but it may be helpful. 3. Lift the HP Netserver by its inner-rails off the floor or pallet. 4. Move the rear of the inner-rails mounted on the Netserver just beyond the inside edge of the outer-rail assemblies. See Figure 13-6. The mounting inner-rails should sit just inside the outer-rails with nothing preventing the Netserver from moving into the outer-rails. Figure 13-6. Mounting the HP Netserver 5. Slowly move the Netserver chassis into the outer-rail assemblies until the Netserver is completely in the rack. See Figure 13-6. 121

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 13
Alternative Rack Mounting (4–Post)
121
1.
Lower the leveler screws on the rack’s lower four corners to make firm
contact with the floor. See Figure 13-4.
2.
Ensure you have extended the anti-tip foot from the rack before continuing
this procedure. See Figure 13-4.
NOTE
The HP Netserver weighs 32 lbs. (14.5 kg.) fully loaded. It is
not necessary to use two people when placing the Netserver
into the rack, but it may be helpful.
3.
Lift the HP Netserver by its inner-rails off the floor or pallet.
4.
Move the rear of the inner-rails mounted on the Netserver just beyond the
inside edge of the outer-rail assemblies. See Figure 13-6.
The mounting inner-rails should sit just inside the outer-rails with nothing
preventing the Netserver from moving into the outer-rails.
Figure 13-6. Mounting the HP Netserver
5.
Slowly move the Netserver chassis into the outer-rail assemblies until the
Netserver is completely in the rack. See Figure 13-6.