HP LH4r HP Netserver LP 1000r User Guide - Page 69

HP Rack Configuration Tools

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Chapter 7 Rack Mounting the HP Netserver (2-Post) NOTE Use the HP Rack Configuration Tools to determine where in the rack to mount the HP Netserver. The tools are available at: http: //www.hp.com/netserver/support 1. Use the mounting brackets to help find the Netserver location on the columns, as shown in Figure 7-2. The screw holes cover a span of only one EIA unit, which is the height requirement of the HP Netserver. 2. Use the masking tape (or marking pen) to mark above the 3rd hole up the on face of both front columns, as shown in Figure 7-2. NOTE The brackets use the 1st and 3rd holes on the respective front columns, regardless of the mounting position of the Netserver. The Netserver can only be mounted into both holes of one EIA Unit, but cannot be mounted across two EIA units. You cannot use a hole in one EIA unit and a hole in another EIA unit. # "#" represents # the hole grouping for EIA units on the # rack columns. # 3rd Hole From Bottom # 1st Hole # From Bottom Left Side Right Side Masking Tape Marker Front of Rack Mark this face of the columns with masking tape or marker pen. Bottom of HP NetServer Figure 7-2. Locations on the Rack's Front Columns 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 7
Rack Mounting the HP Netserver (2-Post)
63
NOTE
Use the
HP Rack Configuration Tools
to determine where in
the rack to mount the HP Netserver. The tools are available at:
http: //www.hp.com/netserver/support
1.
Use the mounting brackets to help find the Netserver location on the
columns, as shown in Figure 7-2.
The screw holes cover a span of only one EIA unit, which is the height
requirement of the HP Netserver.
2.
Use the masking tape (or marking pen) to mark above the 3rd hole up the
on face of both front columns, as shown in Figure 7-2.
NOTE
The brackets use the 1st and 3rd holes on the respective front
columns, regardless of the mounting position of the Netserver.
The Netserver can only be mounted into both holes of one EIA
Unit, but cannot be mounted across two EIA units. You cannot
use a hole in one EIA unit and a hole in another EIA unit.
"
#
"
represents
the hole grouping
for EIA units on the
rack columns.
3rd Hole
From Bottom
1st Hole
From Bottom
Mark this face of
the columns with
masking tape
or marker pen.
Right
Side
Left
Side
Front of
Rack
Bottom of
HP NetServer
#
#
#
#
#
#
Masking
Tape
Marker
Figure 7-2. Locations on the Rack’s Front Columns