HP LH4r HP Netserver LP 1000r User Guide - Page 26

Installing Hot Swap Hard Drives

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Chapter 3 Installing Mass Storage Devices Installing Hot Swap Hard Drives Use this section to install the SCSI hard drives in the Hot Swap drive bays. CAUTION Protect the drive from static electricity by leaving it in its anti-static bag until you are ready to install it. Before handling the drive, touch any unpainted metal surface to discharge static electricity. When you remove the drive from the antistatic bag, handle it only by the frame. Do not touch the electrical components. Place the drive on the anti-static bag whenever you set it down. 1. Remove the filler panel from the desired drive bay location: a. Place a thumb and index finger on the tab latches on the sides of the filler panel, as shown in Figure 3-2. b. Press in on both tab latches to release the filler panel. c. While keeping both tab latches depressed, pull the filler panel out of the drive bay. See Figure 3-2. Tab Latches Figure 3-2. Releasing the Filler Panel's Tab Latches CAUTION 20 Save the filler panel for future use. If the filler panels are left out of empty drive bays while the Netserver is operating, thermal damage and/or excessive EMI could occur.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 3
Installing Mass Storage Devices
20
Installing Hot Swap Hard Drives
Use this section to install the SCSI hard drives in the Hot Swap drive bays.
CAUTION
Protect the drive from static electricity by leaving it in its
anti-static bag until you are ready to install it. Before handling
the drive, touch any unpainted metal surface to discharge
static electricity. When you remove the drive from the anti-
static bag, handle it only by the frame.
Do not touch
the electrical components. Place the drive on the
anti-static bag whenever you set it down.
1.
Remove the filler panel from the desired drive bay location:
a.
Place a thumb and index finger on the tab latches on the sides of the
filler panel, as shown in Figure 3-2.
b.
Press in on both tab latches to release the filler panel.
c.
While keeping both tab latches depressed, pull the filler panel out of the
drive bay. See Figure 3-2.
Tab Latches
Figure 3-2.
Releasing the Filler Panel’s Tab Latches
CAUTION
Save the filler panel for future use. If the filler panels are left
out of empty drive bays while the Netserver is operating,
thermal damage and/or excessive EMI could occur.