HP LH4r HP Netserver LP 1000r User Guide - Page 8

Power On/Off/Sleep, Switch, On/Off/Sleep LED, Steady Green, Blinking Green, Reset Switch

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Chapter 1 CD-ROM Eject Button RESET Controls, Ports, and Indicators FDD Eject Button CD-ROM CD-ROM Activity LED FDD Activity LED Flexible Disk Drive (FDD) SCSI Disk ID 0 SCSI Disk ID 1 SCSI Disk ID 2 Figure 1-2. Input and Storage Device Controls Table 1-1. Power Switch and Indicators Control/Indicator Description Power On/Off/Sleep Switch This push-button switch turns the HP Netserver power On or Off, and if available, also transitions the Netserver between Power On and sleep states. If sleep states are not available, then this button only turns power On or Off. Push-button Switch The sleep states are NOS dependent and not available if your NOS does not support power management based on the ACPI (Advanced Configuration and Power Management Interface) standard. Refer to "Applying Power to the HP Netserver" and "Sleep States (ACPI)" later in this chapter. On/Off/Sleep LED This green LED provides the power state of the Netserver: • Steady Green when the Netserver is operating normally • Blinking Green at 1-Hz rate indicates the Netserver LED is in a sleep state and under ACPI control • Off (unlit) when the Netserver is powered off or in standby Reset Switch This push-button momentary switch creates a hard system reset. This is the equivalent to a power-on reset. RESET Push-button Switch 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 1
Controls, Ports, and Indicators
2
CD-ROM
Flexible Disk Drive
(FDD)
RESET
CD-ROM Eject Button
FDD Activity LED
CD-ROM Activity LED
FDD Eject Button
SCSI Disk ID 0
SCSI Disk ID 1
SCSI Disk ID 2
Figure 1-2. Input and Storage Device Controls
Table 1-1. Power Switch and Indicators
Control/Indicator
Description
Power On/Off/Sleep
Switch
Push-button
Switch
This push-button switch turns the HP Netserver power On
or Off, and if available, also transitions the Netserver
between Power On and sleep states. If sleep states are not
available, then this button only turns power On or Off.
The sleep states are NOS dependent and not available if
your NOS does not support power management based on
the ACPI (Advanced Configuration and Power
Management Interface) standard. Refer to "Applying
Power to the HP Netserver" and "Sleep States (ACPI)"
later in this chapter.
On/Off/Sleep LED
LED
This green LED provides the power state of the Netserver:
•
Steady Green
when the Netserver is operating
normally
•
Blinking Green
at 1-Hz rate indicates the Netserver
is in a sleep state and under ACPI control
•
Off
(unlit) when the Netserver is powered off or in
standby
Reset Switch
RESET
Push-button
Switch
This push-button momentary switch creates a hard system
reset.
This is the equivalent to a power-on reset.