HP LH4r HP Netserver LP 1000r User Guide - Page 39

Refer to Opening and Closing the HP Netserver.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Chapter 4 Installing Additional Memory Refer to the appropriate chapter (Chapters 7, 8, or 13) for instructions. 4. Remove the top cover. Refer to Chapter 2, "Opening and Closing the HP Netserver." NOTE You do not need to remove the system board from the Netserver chassis to install or replace DIMMs. 5. Locate the DIMM slots on the system board. See Figures 4-1 and 4-2. 6. Loosen the two captive screws holding the air duct, which covers the DIMM slots, and remove the air duct. See Figure 4-1. 7. Open the retaining latches. 8. Lift the DIMM completely away from the slot. 9. Place the DIMM in its anti-static container. 10. Repeat Steps 6-9 for as many DIMMs as you need to remove. NOTE If there are no DIMMs installed when you power up the Netserver, you will not get a display on the monitor, but you will hear beep codes. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 4
Installing Additional Memory
33
Refer to the appropriate chapter (Chapters 7, 8, or 13) for instructions.
4.
Remove the top cover.
Refer to Chapter 2, "Opening and Closing the HP Netserver."
NOTE
You do not need to remove the system board from the
Netserver chassis to install or replace DIMMs.
5.
Locate the DIMM slots on the system board. See Figures 4-1 and 4-2.
6.
Loosen the two captive screws holding the air duct, which covers the
DIMM slots, and remove the air duct.
See Figure 4-1.
7.
Open the retaining latches.
8.
Lift the DIMM completely away from the slot.
9.
Place the DIMM in its anti-static container.
10.
Repeat Steps 6-9 for as many DIMMs as you need to remove.
NOTE
If there are no DIMMs installed when you power up the
Netserver, you will not get a display on the monitor, but you
will hear beep codes.