HP LH4r HP Netserver LP 1000r User Guide - Page 27

See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Chapter 3 Installing Mass Storage Devices 2. Remove the SCSI drive from its protective packaging and open the ejector arms as shown in Figure 3-3. The SCSI drive should already be mounted in the Hot Swap mounting tray adapter. a. Place both thumbs in the center opening at the front of the SCSI drive. b. Pull outward on both ejector arms, which moves the locking tabs inward. See Figure 3-4. You should hear the each ejector arm click as you pull it outward. 3. Gently slide the SCSI drive into the chassis, until you feel resistance. See Figure 3-3. The drive will meet resistance about a quarter of an inch before completely seating in the drive bay. 4. Push the drive in firmly (all the way) to seat the drive in the connector on SCSI back plane. Figure 3-3. Inserting the Drive CAUTION To prevent snapping off the ejector arms do not apply excessive pressure. 5. Close the ejector arms by rotating each one back into place. See Figure 3-4. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 3
Installing Mass Storage Devices
21
2.
Remove the SCSI drive from its protective packaging and open the ejector
arms as shown in Figure 3-3.
The SCSI drive should already be mounted in the Hot Swap mounting tray
adapter.
a.
Place both thumbs in the center opening at the front of the SCSI drive.
b.
Pull outward on both ejector arms, which moves the locking tabs
inward.
See Figure
3-4.
You should hear the each ejector arm click as you pull it outward.
3.
Gently slide the SCSI drive into the chassis, until you feel resistance.
See Figure 3-3.
The drive will meet resistance about a quarter of an inch before completely
seating in the drive bay.
4.
Push the drive in firmly (all the way) to seat the drive in the connector on
SCSI back plane.
Figure 3-3. Inserting the Drive
CAUTION
To prevent snapping off the ejector arms do not apply
excessive pressure.
5.
Close the ejector arms by rotating each one back into place. See Figure 3-4.