HP LH4r HP Netserver LP 1000r User Guide - Page 73

See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Chapter 7 Rack Mounting the HP Netserver (2-Post) Figure 7-6. Flush Mounting in the Rack 3. Position the Netserver's two flush mount brackets over the holes (1st & 3rd) on the face of the two columns. See Figure 7-6. The masking tape or marking pen (marker) should provide the location of the holes on the two columns. See Figure 7-2. 4. Insert one screw through each bracket into the column, preferably the top or 1st hole on the column below the marker. 5. Turn the two screws enough with the Torx driver to hold the Netserver in place, while you insert the two remaining screws. 6. If mounting the Netserver with the center mounts, follow Steps 1-5 for the center mount brackets. See Figure 7-7. 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 7
Rack Mounting the HP Netserver (2-Post)
67
Figure 7-6. Flush Mounting in the Rack
3.
Position the Netserver’s two flush mount brackets over the holes (1st &
3rd) on the face of the two columns.
See Figure 7-6.
The masking tape or marking pen (marker) should provide the location of
the holes on the two columns. See Figure 7-2.
4.
Insert one screw through each bracket into the column, preferably the top
or 1st hole on the column below the marker.
5.
Turn the two screws enough with the Torx driver to hold the Netserver in
place, while you insert the two remaining screws.
6.
If mounting the Netserver with the center mounts, follow Steps 1-5 for the
center mount brackets.
See Figure 7-7.