HP LH4r HP Netserver LP 1000r User Guide - Page 16

Replacing the Front Bezel

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Chapter 2 Opening and Closing the HP Netserver 4. Pull and lift the bezel out toward you and remove it from the chassis. See Figure 2-1. Pins Spring Latch (2) Figure 2-1. Front Bezel Location NOTE The front bezel pivots on two pins at the bottom and is held in place at the top with spring latches holding onto the top pins. The middle pins limit bezel rotation to an 80° angle. Replacing the Front Bezel 1. Place the bottom edge of the front bezel into the hinge pins at the bottom front of the chassis. 2. Rotate the top front of the bezel into place and push it in at the top, allowing it to snap into place. The spring latches grasp the pins at the top and hold the bezel in place. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 2
Opening and Closing the HP Netserver
10
4.
Pull and lift the bezel out toward you and remove it from the chassis. See
Figure 2-1.
Spring
Latch (2)
Pins
Figure 2-1. Front Bezel Location
NOTE
The front bezel pivots on two pins at the bottom and is held in
place at the top with spring latches holding onto the top pins.
The middle pins limit bezel rotation to an 80
°
angle.
Replacing the Front Bezel
1.
Place the bottom edge of the front bezel into the hinge pins at the bottom
front of the chassis.
2.
Rotate the top front of the bezel into place and push it in at the top,
allowing it to snap into place.
The spring latches grasp the pins at the top and hold the bezel in place.