HP LH4r HP Netserver LP 1000r User Guide - Page 41

Installing Additional Boards

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

5 Installing Additional Boards Introduction The HP Netserver LP 1000r provides one 64-bit PCI slot connected to a riser board on the system board, which will handle a full-length 32-bit or 64-bit PCI accessory board. Tested PCI Boards For a list of tested PCI boards, check for compatibility in Configuration Assistant on the Navigator CD-ROM or look for the Hardware Tested Products list for the HP Netserver LP 1000r under the Service and Support topic for the specific NOS used in the Netserver at HP's web site: http://www.hp.com/netserver/support/ CAUTION Some accessory board outputs may exceed U.S. National Electrical code (NFPA 70) Class 2 or limited power source limits and must use appropriate interconnecting cabling in accordance with the National Electrical Code. NOTE All Hewlett-Packard accessory boards comply with the U.S. National Electrical code (NFPA 70) Class 2. Also refer to the Readme file and Configuration Advisor on your HP Netserver Navigator CD-ROM. Refer to Chapter 10, "Configuring the HP Netserver," for instructions. Tools Required The following tools are only needed when removing or adding an accessory board in the HP Netserver: • An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit includes a static-dissipating work surface, a chassis clip lead, and a wrist strap. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
35
5
Installing Additional Boards
Introduction
The HP Netserver LP 1000r provides one 64-bit PCI slot connected to a riser
board on the system board, which will handle a full-length 32-bit or 64-bit PCI
accessory board.
Tested PCI Boards
For a list of tested PCI boards, check for compatibility in Configuration Assistant
on the Navigator CD-ROM or look for the Hardware Tested Products list for the
HP Netserver LP 1000r under the Service and Support topic for the specific NOS
used in the Netserver at HP’s web site:
CAUTION
Some accessory board outputs may exceed U.S. National
Electrical code (NFPA 70) Class 2 or limited power source
limits and must use appropriate interconnecting cabling in
accordance with the National Electrical Code.
NOTE
All Hewlett-Packard accessory boards comply with the U.S.
National Electrical code (NFPA 70) Class 2.
Also refer to the Readme file and Configuration Advisor on your
HP Netserver
Navigator CD-ROM
. Refer to Chapter 10, "Configuring the HP Netserver," for
instructions.
Tools Required
The following tools are only needed when removing or adding an accessory board
in the HP Netserver:
•
An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit
includes a static-dissipating work surface, a chassis clip lead, and a wrist
strap.