HP LH4r HP Netserver LP 1000r User Guide - Page 38

Removing DIMMs

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Chapter 4 Installing Additional Memory DIMM 0 1 Slots 2 3 System Board Figure 4-4. DIMM Insertion 12. Repeat Steps 7-11 to install all of the DIMMs for your memory configuration. 13. If you have completed the DIMM installation, close the Netserver and return it to the rack where power can be applied. Removing DIMMs You may need to remove a DIMM module to downsize your memory configuration or to replace a defective DIMM. 1. If the HP Netserver is already installed and working, power down the Netserver. Refer to Chapter 1, "Controls, Ports, and Indicators." 2. Disconnect the power cables and all external cables. If necessary, label each one to support re-assembly. WARNING The power supply will continue to provide standby current to the Netserver until the power cable is disconnected. 3. Remove the Netserver chassis from the rack and lay it on a flat surface. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 4
Installing Additional Memory
32
DIMM
Slots
0
1
3
2
System Board
Figure 4-4. DIMM Insertion
12.
Repeat Steps 7-11 to install all of the DIMMs for your memory
configuration.
13.
If you have completed the DIMM installation, close the Netserver and
return it to the rack where power can be applied.
Removing DIMMs
You may need to remove a DIMM module to downsize your memory
configuration or to replace a defective DIMM.
1.
If the HP Netserver is already installed and working, power down the
Netserver.
Refer to Chapter 1, "Controls, Ports, and Indicators."
2.
Disconnect the power cables and all external cables.
If necessary, label each one to support re-assembly.
WARNING
The power supply will continue to provide standby current to
the Netserver until the power cable is disconnected.
3.
Remove the Netserver chassis from the rack and lay it on a flat surface.