HP LH4r HP Netserver LP 1000r User Guide - Page 17

Removing the Top Cover

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Chapter 2 Opening and Closing the HP Netserver Removing the Top Cover To remove the top cover, follow these steps: NOTE You do not need to removal the front bezel to remove the top cover of the Netserver. 1. If the HP Netserver is operating, log off all users and shutdown the operating system. Refer to the instructions in Chapter 1, "Controls, Ports, and Indicators." 2. Disconnect the power cord and any cables attached to the Netserver. 3. Remove the Netserver chassis from the rack and lay it on a flat surface. Refer to the instructions in Chapters 7, 8, or 13 (depending on the rack type) to remove the chassis from the rack. NOTE Some rack mounting options (slides) do not require removing the HP Netserver chassis from the rack and laying it on a flat surface to access the internal components. 4. Release the top cover by turning the knob at the front of the chassis to "Open" position (clockwise direction). See Figure 2-2. 5. Slide the top cover about 1½ inch (38 mm) toward the front of the Netserver and then lift it off the chassis. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 2
Opening and Closing the HP Netserver
11
Removing the Top Cover
To remove the top cover, follow these steps:
NOTE
You do not need to removal the front bezel to remove the top
cover of the Netserver.
1.
If the HP Netserver is operating, log off all users and shutdown the
operating system.
Refer to the instructions in Chapter 1, "Controls, Ports, and Indicators."
2.
Disconnect the power cord and any cables attached to the Netserver.
3.
Remove the Netserver chassis from the rack and lay it on a flat surface.
Refer to the instructions in Chapters 7, 8, or 13 (depending on the rack
type) to remove the chassis from the rack.
NOTE
Some rack mounting options (slides) do not require removing
the HP Netserver chassis from the rack and laying it on a flat
surface to access the internal components.
4.
Release the top cover by turning the knob at the front of the chassis to
"Open" position (clockwise direction). See Figure 2-2.
5.
Slide the top cover about 1½ inch (38 mm) toward the front of the
Netserver and then lift it off the chassis.