HP LH4r HP Netserver LP 1000r User Guide - Page 30

Optional SCSI Drive Controller

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Chapter 3 Installing Mass Storage Devices CAUTION Figure 3-5. Removing a Hot Swap Drive To prevent overheating or excessive electromagnetic radiation, use the filler panels to fill the unused drive bays. If the filler panels are left out of empty drive bays while the Netserver is operating, thermal damage and/or excessive EMI could occur. Optional SCSI Drive Controller Typically, this option is only used when hardware mirroring the Hot Swap SCSI drives. To change control of the SCSI drives requires installation of a supported HP NetRAID controller board and moving the connection of the existing SCSI cable. One end is moved from the SCSI A cable connection on the system board to the SCSI connector on the supported HP NetRAID Controller board. 1. Refer to Chapter 5, "Installing Additional Boards," to access the Netserver. CAUTION Don't disconnect the SCSI cable on the SCSI backplane board. This cable end remains connected while moving the other end of the cable at the SCSI A connector on the system board. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 3
Installing Mass Storage Devices
24
Figure 3-5.
Removing a Hot Swap Drive
CAUTION
To prevent overheating or
excessive electromagnetic
radiation, use the filler panels to fill the unused drive bays. If
the filler panels are left out of empty drive bays while the
Netserver is operating, thermal damage and/or excessive EMI
could occur.
Optional SCSI Drive Controller
Typically, this option is only used when hardware mirroring the Hot Swap SCSI
drives. To change control of the SCSI drives requires installation of a supported
HP NetRAID controller board and moving the connection of the existing SCSI
cable.
One end is moved from the SCSI A cable connection on the system board
to the SCSI connector on the supported HP NetRAID Controller board.
1.
Refer to Chapter 5, "Installing Additional Boards," to access the Netserver.
CAUTION
Don’t disconnect the SCSI cable on the SCSI backplane board.
This cable end remains connected while moving the other end
of the cable at the SCSI A connector on the system board.