HP LH4r HP Netserver LP 1000r User Guide - Page 54

Refer to Opening and Closing the HP Netserver, to gain

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Chapter 6 Installing an Additional Processor Refer to Chapter 2, "Opening and Closing the HP Netserver," to gain access to the system board. NOTE It is not necessary to remove the system board from the Netserver to install the second processor (CPU 2). 6. Loosen the two captive screws holding the air duct over the DIMM slots and remove the air duct. See Figure 6-2. Figure 6-2. Removing the Air duct 7. Ensure the processor speed of the second processor (CPU 2) is the same as the existing processor before installing the second processor. NOTE If you are upgrading the second processor to a faster processor speed than the primary processor, the primary processor must also be changed. Both processors must have the same product number, which includes the same clock speed, cache size, and FSB speed. The supported processors only perform at the rated speed indicated on the processor in the HP Netserver. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 6
Installing an Additional Processor
48
Refer to Chapter 2, "Opening and Closing the HP Netserver," to gain
access to the system board.
NOTE
It is not necessary to remove the system board from the
Netserver to install the second processor (CPU 2).
6.
Loosen the two captive screws holding the air duct over the DIMM slots
and remove the air duct.
See Figure 6-2.
Figure 6-2. Removing the Air duct
7.
Ensure the processor speed of the second processor (CPU 2) is the same as
the existing processor before installing the second processor.
NOTE
If you are upgrading the second processor to a faster processor
speed than the primary processor, the primary processor must
also be changed. Both processors must have the same product
number, which includes the same clock speed, cache size, and
FSB speed.
The supported processors only perform at the rated speed
indicated on the processor in the HP Netserver.