Home » IBM Manuals » Desktops » IBM 847651U » Manual Viewer

IBM 847651U Handbook - Page 208

POST message, Description, System Security, AssetCare, Asset ID, Enabled, System, Security.,

UPC - 087944496366

Add to My Manuals
Save this manual to your list of manuals

Page 208 highlights

POST Messages POST message 177 183 184 186 187 190 Description A security (inventory) violation has occurred. The Asset Control System Security feature has detected that the values for AssetCare and Asset ID have been set to Enabled, and the server has been moved without authorization. Action: You must enter the administrator password to clear this POST message. From the Configuration/Setup Utility menu, select System Security. Then, follow the instructions on the screen. Set the values for AssetCare and Asset ID to Disabled. For information on using the Configuration/Setup Utility program, see "Using the Configuration/Setup Utility program" on page 39. If the problem persists, have the system serviced. The privileged-access protection message is received if the administrative password has been enabled. Action: You must enter the administrator password to clear this POST message. If the message recurs when the cover has not been removed, have the system serviced. Invalid power-on password checksum received. The values for AssetCare and Asset ID have been set to Enabled, and an RFID Antenna has been installed. Action: From the Configuration/Setup Utility menu, select System Security. Then, follow the instructions on the screen. Set the values for AssetCare and Asset ID to Disabled. An RFID Antenna should not be installed. For information on using the Configuration/Setup Utility program, see "Using the Configuration/Setup Utility program" on page 39. If this information cannot be restored, have the system serviced. A system board or hardware security error has been cleared. Action: The administrator password was entered to clear POST message 176. No further action is required. The administrator password and startup (boot) sequences have been cleared. POST message 162 will normally display also. Action: See POST message 162 The server tamper indicator was cleared. Action: No action is required. 174 Netfinity 3000 User's Handbook

Section	Page
Tables	9
Caution and danger statements	11
Instruções de Cuidado e Perigo (Português do Brasil)	11
Sikkerhedsforskrifter mærket Pas på! og Fare! (dansk)	13
Turvaohjeet (suomi)	14
Consignes Attention et Danger (Français)	14
Sicherheitshinweise (Deutsch)	15
Avvisi di attenzione e di pericolo (Italiano)	16
Veiligheidsinstructies (Nederlands)	18
Advarsels- og faremerknader (norsk)	19
Notas de Cuidado e de Perigo (Português)	20
Declaraciones sobre precauciones y peligros (español)	22
Varningsmeddelanden (Svenska)	22
Safety information	25
Lithium battery notice	27
Laser compliance statements	28
About this book	31
How this book is organized	31
Notices used in this book	32
Related publications	33
Chapter 1. Introducing your Netfinity 3000 server	35
Features at a glance	37
What your IBM Netfinity 3000 server offers	38
Reliability, availability, and serviceability features	41
Controls and indicators	42
Input/output connectors	45
Internal view	49
External view	50
Chapter 2. Getting started	51
Questions or problems?	53
Arranging your workspace	54
Using the stabilizing feet	57
Cabling the server	58
Starting the server	60
Using the CD-ROM drive	64
Chapter 3. Configuring your server	67
Configuration overview	68
The Configuration/Setup Utility program	70
Using the Configuration/Setup Utility program	73
Resolving configuration conflicts	91
Configuring the Ethernet controller	93
Using the SCSISelect Utility program	96
Chapter 4. Installing options	101
Before you begin	103
Electrical safety	104
Handling static-sensitive devices	105
Preparing to add options	107
Working with adapters	113
Working with memory modules	130
Installing or removing internal drives	136
Working with microprocessors	160
Connecting external options	167
Adding security options	178
Completing the installation	182
Updating the server configuration	187
Network operating system instructions	188
Chapter 5. Solving problems	191
Diagnostic tools overview	192
Running the diagnostic test programs	198
Power-on self-test (POST) messages	199
Power-on self-test (POST) beep codes	226
SCSI messages	228
Ethernet controller messages	230
Troubleshooting	234
Checking the system for damage	256
Replacing the battery	258
Chapter 6. Getting help, service, and information	263
Service support	264
Before you call for service	266
Getting customer support and service	266
Purchasing additional services	272
Ordering publications	274
Chapter 7. Server records and specifications	277
Recording the identification numbers	278
Recording installed devices	279
System specifications	285
Appendix A. Ethernet cable specifications	305
Appendix B. Product warranties and notices	309
Warranty Statements	309
Notices	320
Electronic emission notices	323
Power cords	326
Glossary	329

Match case Limit results 1 per page

POST Messages

POST message

Description

177

A security (inventory) violation has occurred.

The Asset Control

System Security

feature has detected that the

values for

AssetCare

and

Asset ID

have been set to

Enabled

, and

the server has been moved without authorization.

Action:

You must enter the administrator password to clear this

POST message.

From the Configuration/Setup Utility menu, select

System

Security.

Then, follow the instructions on the screen.

Set the

values for

AssetCare

and

Asset ID

Disabled

. For information

on using the Configuration/Setup Utility program, see “Using

the Configuration/Setup Utility program” on page

39.

If the problem persists, have the system serviced.

183

The privileged-access protection message is received if the

administrative password has been enabled.

Action:

You must enter the administrator password to clear this

POST message.

If the message recurs when the cover has not

been removed, have the system serviced.

184

Invalid power-on password checksum received.

The values for

AssetCare

and

Asset ID

have been set to

Enabled

and an RFID Antenna has been installed.

Action:

From the Configuration/Setup Utility menu, select

System

Security.

Then, follow the instructions on the screen.

Set the

values for

AssetCare

and

Asset ID

Disabled

. An RFID

Antenna should not be installed.

For information on using the

Configuration/Setup Utility program, see “Using the

Configuration/Setup Utility program” on page

39.

If this information cannot be restored, have the system serviced.

186

A system board or hardware security error has been cleared.

Action:

The administrator password was entered to clear POST

message 176.

No further action is required.

187

The administrator password and startup (boot) sequences have

been cleared.

POST message 162 will normally display also.

Action:

See POST message

162

190

The server tamper indicator was cleared.

Action:

No action is required.

174

Netfinity 3000 User's Handbook