Kenwood TH-D75 User Manual - Page 37

CROSS TONE, Using Cross Tone

Get Kenwood TH-D75 PDF manuals and user guides View all Kenwood TH-D75 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

2 Press [F], press and hold [TONE]. • Scan starts and "Scanning" blinks on the display. • To quit the scan, press [ ]. • When a DCS code is identified, the identified code appears on the display and blinks. 3 Press [A/B] to program the identified code in place of the currently set DCS code. • The DCS function will remain on. To cancel DCS, press [TONE] until DCS no longer appears on the display. CROSS TONE Using Cross Tone You can set separate signaling types by TX and RX for when you access a repeater that uses different Encode/ decode signaling. To turn the Cross Tone function On: 1 Press [TONE] 4 times to activate the Cross Tone function. • The < > (default) icon appears on the display when the Cross Tone function is On. • Each time you press [TONE], the selection changes as follows: Tone ( )  CTCSS ( )  DCS ( )  Cross Tone ( : default)  Off (no display). • Additionally, when APRS is ON and Voice Alert is configured, Voice Alert ON is added to the above cycle. Selecting a Cross Tone mode To select the cross tone/code frequency required to access your desired repeater: 1 Turn the Cross Tone function On. 2 Press [F], [TONE]. • The Cross Tone setting appears on the display. 3 Select your desired Cross Tone setting. Setting DCS/Off Encode DCS Decode off TONE/DCS Tone DCS DCS/CTCSS DCS CTCSS TONE/CTCSS Tone CTCSS 4 Press [A/B] to set the selected setting. Icon 10-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
10-3
2
Press
[F],
press and hold
[TONE]
.
•
Scan starts and
“
Scanning
”
blinks on the display.
•
To quit the scan, press
[
]
.
•
When a DCS code is identified, the identified code
appears on the display and blinks.
3
Press
[A/B]
to program the identified code in place of the
currently set DCS code.
•
The DCS function will remain on. To cancel DCS, press
[TONE]
until DCS no longer appears on the display.
CROSS TONE
Using Cross Tone
You can set separate signaling types by TX and RX for when
you access a repeater that uses different Encode/ decode
signaling.
To turn the Cross Tone function On:
1
Press
[TONE]
4 times to activate the Cross Tone function.
•
The <
>
(default) icon appears on the display when
the Cross Tone function is On.
•
Each time you press
[TONE]
, the selection changes as
follows:
Tone (
)
CTCSS (
)
DCS (
)
Cross
Tone (
: default)
Off (no display).
•
Additionally, when APRS is ON and Voice Alert is
configured, Voice Alert ON is added to the above cycle.
Selecting a Cross Tone mode
To select the cross tone/code frequency required to access
your desired repeater:
1
Turn the Cross Tone function On.
2
Press
[F]
,
[TONE]
.
•
The Cross Tone setting appears on the display.
3
Select your desired Cross Tone setting.
Setting
Encode
Decode
Icon
DCS/Off
DCS
off
TONE/DCS
Tone
DCS
DCS/CTCSS
DCS
CTCSS
TONE/CTCSS
Tone
CTCSS
4
Press
[A/B]
to set the selected setting.