Kenwood TH-D75 User Manual - Page 95

Displaying The Repeater Details, Fast Data Communication, Emr Communication

Get Kenwood TH-D75 PDF manuals and user guides View all Kenwood TH-D75 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

DISPLAYING THE REPEATER DETAILS You can check the details information of the repeater. 1 Select [Repeater Detail] in the Digital Function Menu. The confirmation screen appears. Data TX End Timing This function is to set the delay time until return from fast data TX to RX in accordance with the TX timing of the PC software. 1 Access Menu No. 614. 2 Press [ ]/[ ]. Each press switches between the access repeater details screen and gateway CQ repeater details screen. FAST DATA COMMUNICATION Fast data communications can be performed by using the voice band for data communications when operating in DV/DR mode. 1 Access Menu No. 984. Select the method for connecting (USB or Bluetooth) with the external device for data communication. 2 Select [Data Mode] in the Digital Function Menu. When the data mode is set, the < the display. > icon appears on Connecting with a PC Use a commercially available data communication cable to connect the USB connector of the transceiver to a PC. Software Setting for Data Communication Refer to the followings and complete the settings. Port: Select the COM port number used by this transceiver. Note: ¡ The COM port number used by this transceiver may be 5 or higher depending on the PC environment. In this case, use a communication software that allows you to set the COM port number to 5 or higher. Data Communication Operation When performing data communication operation, refer to the instruction manual of the communication software. 1 Set the Callsign of your station, the other station, and repeater. 2 Perform the operation according to the instruction manual and other documents of the communication software. 3 When a text is entered in the communication software screen, that text will be transmitted automatically. 2 Select [Off], [0.5], [1], [1.5], or [2] seconds. EMR COMMUNICATION The Enhanced Monitor Request (EMR) mode is a function used in DV/DR mode to, for example, contact somebody in an emergency. Note: ¡ This function is forced to open the squelch of all of the transceivers, which have received the EMR signal, and then to the state to receive the signal. And easily send the EMR signal, please note that you will cause to give trouble to the other station. ¡ Setting the other station Callsign or CQ are maintained. ¡ Selecting EMR in EMR mode will cancel EMR mode. ¡ EMR setting is canceled when the power is switched OFF. ¡ EMR communication is not recorded in the TX history. ¡ Any station that received the EMR communication displays the EMR call icon < > during receiving. 1 Select [Destination Select] in the Digital Function Menu. The destination selection screen appears. 2 Select [EMR] and press [ENT]. [EMR] is set. 3 Press [PTT] to transmit. Adjusting the Volume for EMR Signal Reception You can set the volume level within the range of 1 to 50 when an EMR signal is received. However, if the volume level set by the [VOL] control is higher, the reception will be at that volume. 1 Access Menu No. 615. 2 Select the volume level among from [1] to [50], and press [A/B]. 3 The volume is set. 16-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
16-9
DISPLAYING THE REPEATER DETAILS
You can check the details information of the repeater.
1
Select [Repeater Detail] in the Digital Function Menu.
The confirmation screen appears.
2
Press
[
]/[
].
Each press switches between the access repeater details
screen and gateway CQ repeater details screen.
FAST DATA COMMUNICATION
Fast data communications can be performed by using the
voice band for data communications when operating in DV/DR
mode.
1
Access Menu No. 984.
Select the method for connecting (USB or Bluetooth) with
the external device for data communication.
2
Select [Data Mode] in the Digital Function Menu.
When the data mode is set, the <
> icon appears on
the display.
Connecting with a PC
Use a commercially available data communication cable to
connect the USB connector of the transceiver to a PC.
Software Setting for Data Communication
Refer to the followings and complete the settings.
Port: Select the COM port number used by this transceiver.
Note:
¡
The COM port number used by this transceiver may be 5 or
higher depending on the PC environment. In this case, use a
communication software that allows you to set the COM port
number to 5 or higher.
Data Communication Operation
When performing data communication operation, refer to the
instruction manual of the communication software.
1
Set the Callsign of your station, the other station, and
repeater.
2
Perform the operation according to the instruction manual
and other documents of the communication software.
3
When a text is entered in the communication software
screen, that text will be transmitted automatically.
Data TX End Timing
This function is to set the delay time until return from fast data
TX to RX in accordance with the TX timing of the PC software.
1
Access Menu No. 614.
2
Select [Off], [0.5], [1], [1.5], or [2] seconds.
EMR COMMUNICATION
The Enhanced Monitor Request (EMR) mode is a function
used in DV/DR mode to, for example, contact somebody in an
emergency.
Note:
¡
This function is forced to open the squelch of all of the
transceivers, which have received the EMR signal, and then to
the state to receive the signal. And easily send the EMR signal,
please note that you will cause to give trouble to the other
station.
¡
Setting the other station Callsign or CQ are maintained.
¡
Selecting EMR in EMR mode will cancel EMR mode.
¡
EMR setting is canceled when the power is switched OFF.
¡
EMR communication is not recorded in the TX history.
¡
Any station that received the EMR communication displays the
EMR call icon <
> during receiving.
1
Select [Destination Select] in the Digital Function Menu.
The destination selection screen appears.
2
Select [EMR] and press
[ENT
].
[EMR] is set.
3
Press
[PTT]
to transmit.
Adjusting the Volume for EMR Signal Reception
You can set the volume level within the range of 1 to 50 when
an EMR signal is received. However, if the volume level set
by the
[VOL]
control is higher, the reception will be at that
volume.
1
Access Menu No. 615.
2
Select the volume level among from [1] to [50], and press
[A/B
].
3
The volume is set.