Lenovo NetVista Hardware Maintenence Manual for Netvista 6838 and 6848 systems - Page 10

Power Management, APM BIOS Mode, Disabled, Automatic Hardware Power Management

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

If the Power Management feature is enabled, do the following: 1. Start the Configuration/Setup Utility program (see "Starting the Configuration/Setup Utility program" on page 19.) 2. Select Power Management from the Configuration/Setup Utility program menu. 3. Select APM. 4. Be sure APM BIOS Mode is set to Disabled. If it is not, press Left Arrow (←) or Right Arrow (→) to change the setting. 5. Select Automatic Hardware Power Management. 6. Set Automatic Hardware Power Management to Disabled. 7. If the problem persists, continue to 003 . 003 Run the Diagnostic programs. If necessary, refer to "Starting the diagnostic programs" on page 9. v If you receive an error, replace the part that the diagnostic program calls out or go to Chapter 3, "Diagnostics", on page 7. v If the test stops and you cannot continue, replace the last device tested. 2 IBM NetVista Type 6838, 6848: Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
If the Power Management feature is enabled, do the following:
1.
Start the Configuration/Setup Utility program (see “Starting the
Configuration/Setup Utility program” on page 19.)
2.
Select
Power Management
from the Configuration/Setup Utility program
menu.
3.
Select
APM
.
4.
Be sure
APM BIOS Mode
is set to
Disabled
. If it is not, press Left Arrow (
←
) or
Right Arrow (
→
) to change the setting.
5.
Select
Automatic Hardware Power Management
.
6.
Set
Automatic Hardware Power Management
to
Disabled
.
7.
If the problem persists, continue to
±003²
.
±003²
Run the Diagnostic programs. If necessary, refer to “Starting the diagnostic
programs” on page 9.
v
If you receive an error, replace the part that the diagnostic program calls out or
go to Chapter 3, “Diagnostics”, on page 7.
v
If the test stops and you cannot continue, replace the last device tested.
2
IBM NetVista Type 6838, 6848: Hardware Maintenance Manual