Netgear WNDAP360 WNDAP360 Reference Manual - Page 101

Table 28., Wireless Signal Repeating Profile and Authentication Settings Continued

Get Netgear WNDAP360 PDF manuals and user guides View all Netgear WNDAP360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

ProSafe Dual Band Wireless-N Access Point WNDAP360 Table 28. Wireless Signal Repeating Profile and Authentication Settings (Continued) Field Description Network Authentication Open System and Data Encryption (continued) Although you can use the bridge communication without any authentication and encryption, NETGEAR recommends that you use WEP if you do select an open system. From the Data Encryption drop-down list, select one of the following: • None. No authentication and encryption. • 64-bit WEP. Standard WEP encryption, using 40/64-bit encryption. • 128-bit WEP. Standard WEP encryption, using 104/128-bit encryption. • 152-bit WEP. Proprietary WEP encryption mode, using 128+24 bits encryption. This mode functions only with other wireless station that support this mode. WPA-PSK TKIP (Temporal Key Integrity Protocol) is the standard encryption method used with WPA-PSK and the only selection possible from the Data Encryption drop-down list. In the WPA Passphrase (Network Key) field, enter a passphrase. The passphrase length needs to be between 8 and 63 characters (inclusive). WPA2-PSK AES (Advanced Encryption Standard) is the standard encryption method used with WPA2-PSK and the only selection possible from the Data Encryption drop-down list. In the WPA Passphrase (Network Key) field, enter a passphrase. The passphrase length needs to be between 8 and 63 characters (inclusive). Note: NETGEAR recommends WPA2-PSK authentication with AES encryption if you want to use the 11n rates and speed. Link Test IP Address To verify the connection between the access point and the wireless station that you intend to build a bridge with, enter the IP address of the wireless station, and then click Link Test. The Link Test Process Status field displays the results of the test (Uninitialized, In Process, Success, Timed Out, or Failure). Note: You should be able to ping the IP address of both APs from a connected client. Failure to ping one of the APs means that the wireless signal is not traversing the bridge. Failure to ping both IP addresses means that the clients is not connected correctly. g. Click Apply to save your security profile settings. The Bridging screen displays again. h. Repeat step d through step g for any other security profile that you want to edit. For example, first configure security profile NETGEAR-WDS-1 with the MAC address of AP1, and then configure security profile NETGEAR-WDS-2 with the MAC address of AP3 (see Figure 59 on page 98). Advanced Configuration 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
Advanced Configuration
101
ProSafe Dual Band Wireless-N Access Point WNDAP360
g.
Click
Apply
to save your security profile settings. The Bridging screen displays
again.
h.
Repeat
step d
through
step g
for any other security profile that you want to edit.
For example, first configure security profile NETGEAR-WDS-1 with the MAC address
of AP1, and then configure security profile NETGEAR-WDS-2 with the MAC address
of AP3 (see
Figure 59
on page 98).
Network Authentication
and
Data Encryption
(continued)
Open System
Although you can use the bridge communication without any
authentication and encryption, NETGEAR recommends that
you use WEP if you do select an open system. From the
Data Encryption drop-down list, select one of the following:
•
None
. No authentication and encryption.
•
64-bit WEP
. Standard WEP encryption, using 40/64-bit
encryption.
•
128-bit WEP
. Standard WEP encryption, using 104/128-bit
encryption.
•
152-bit WEP
. Proprietary WEP encryption mode, using
128+24 bits encryption. This mode functions only with
other wireless station that support this mode.
WPA-PSK
TKIP
(Temporal Key Integrity Protocol) is the standard
encryption method used with WPA-PSK and the only
selection possible from the Data Encryption drop-down list.
In the WPA Passphrase (Network Key) field, enter a
passphrase. The passphrase length needs to be between
8 and 63 characters (inclusive).
WPA2-PSK
AES
(Advanced Encryption Standard) is the standard
encryption method used with WPA2-PSK and the only
selection possible from the Data Encryption drop-down list.
In the WPA Passphrase (Network Key) field, enter a
passphrase. The passphrase length needs to be between
8 and 63 characters (inclusive).
Note:
NETGEAR recommends WPA2-PSK authentication
with AES encryption if you want to use the 11n rates and
speed.
Link Test
IP Address
To verify the connection between the access point and the wireless station
that you intend to build a bridge with, enter the IP address of the wireless
station, and then click
Link Test
. The Link Test Process Status field displays
the results of the test (Uninitialized, In Process, Success, Timed Out, or
Failure).
Note:
You should be able to ping the IP address of both APs from a
connected client. Failure to ping one of the APs means that the wireless signal
is not traversing the bridge. Failure to ping both IP addresses means that the
clients is not connected correctly.
Table 28.
Wireless Signal Repeating Profile and Authentication Settings (Continued)
Field
Description