Home » Netgear Manuals » Wireless » Netgear WNDAP360 » Manual Viewer

Netgear WNDAP360 WNDAP360 Reference Manual - Page 31

Ceiling Installation, To install the wireless access point using the ceiling installation kit

Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

ProSafe Dual Band Wireless-N Access Point WNDAP360 Ceiling Installation  To install the wireless access point using the ceiling installation kit: 1. Verify the package content of the ceiling installation kit. Mounting plate Clamp with screws 2. Detach the mounting plate from the wireless access point. 3. Attach the clamp to the ceiling rail. Installation and Basic Configuration 31

Section	Page
ProSafe Dual Band Wireless-N Access Point WNDAP360	1
Contents	3
1. Introduction	6
About the ProSafe Dual Band Wireless-N Access Point WNDAP360	6
What Is In the Box?	7
System Requirements	7
Key Features and Standards	8
Supported Standards and Conventions	8
Key Features	9
802.11b/g/n and 802.11a/n Standards–Based Wireless Networking	10
Autosensing Ethernet Connections with Auto Uplink	10
Hardware Description	11
Top Panel	11
Rear Panel	12
Bottom Panel with Product Label	13
2. Installation and Basic Configuration	14
What You Need before You Begin	14
Wireless Equipment Placement and Range Guidelines	14
Ethernet Cabling Requirements	15
LAN Configuration Requirements	15
Computer Hardware Requirements	15
Install and Configure the Wireless Access Point	15
Connect the Wireless Access Point to Computer	16
Log In to the Wireless Access Point	17
Configure Basic General System Settings and Time Settings	19
Configure IP Settings and Optional DHCP Server Settings	21
Configure Basic Wireless Settings	23
Operating Frequency (Channel) Guidelines	29
Test Basic Wireless Connectivity	30
Mount the Wireless Access Point	30
Ceiling Installation	31
Wall Installation	33
Desk Installation	35
3. Wireless Configuration and Security	36
Wireless Data Security Options	36
Security Profiles	38
Before You Change the SSID, WEP, and WPA Settings	39
Configure and Enable Security Profiles	42
Configure RADIUS Server Settings	51
Restrict Wireless Access by MAC Address	53
Schedule the Wireless Radio to Be Turned Off	55
Configure Basic Wireless Quality of Service	56
4. Management	58
Enable Remote Management	58
SNMP Management	59
Secure Shell and Telnet Management	60
Upgrade the Wireless Access Point Software	61
Manage the Configuration File or Reset to Factory Defaults	64
Save the Configuration	64
Restore the Configuration	65
Restore the Wireless Access Point to the Factory Default Settings	66
Reboot the Wireless Access Point without Restoring the Default Configuration	67
Change the Administrator Password	68
Enable the Syslog Server	69
Monitor the Wireless Access Point	69
View System Information	70
Monitor Wireless Stations	72
View the Activity Log	75
Traffic Statistics	75
Enable Rogue AP Detection and Monitor Access Points	77
Enable and Configure Rogue AP Detection	77
View and Save Access Point Lists	79
5. Advanced Configuration	81
Spanning Tree Protocol and 802.1Q VLAN	81
Hotspot Settings	83
Configure Advanced Wireless Settings	84
Configure Advanced QoS Settings	86
Configure Wireless Bridging	89
Configure a Point-to-Point Wireless Network	90
Configure a Point-to-Multipoint Wireless Network	93
Configure the Wireless Access Point to Repeat the Wireless Signal Using Point-to-Multipoint Bridge Mode	98
6. Troubleshooting	103
Basic Functioning	104
No LEDs Are Lit on the Wireless Access Point	104
The Active LED or the LAN LED Is Not Lit	105
The WLAN LED Does Not Light Up	105
You Cannot Access the Internet or the LAN from a Wireless-Capable Computer	105
You Cannot Configure the Wireless Access Point from a Browser	106
When You Enter a URL or IP Address a Time-Out Error Occurs	107
Troubleshooting a TCP/IP Network Using the Ping Utility	107
Testing the LAN Path to Your Wireless Access Point	107
Testing the Path from Your Computer to a Remote Device	108
Problems with Date and Time	108
Use the Packet Capture Tool	109
A. Supplemental Information	110
Technical Specifications	110
Factory Default Settings	112
B. Command-Line Reference	115
C. Notification of Compliance	128