Sony STR-DN1070 Help Guide Printable PDF - Page 43

Performing Auto Calibration

Get Sony STR-DN1070 PDF manuals and user guides View all Sony STR-DN1070 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

SPA+B (*): Speakers connected to both the SPEAKERS FRONT A and SPEAKERS SURROUND BACK/BI-AMP/FRONT HIGH/FRONT B terminals (parallel connection). (None): [SPK OFF] appears on the display panel. No audio signals are output from any speaker terminals. * To select [SPB] or [SPA+B], set the assignment for the SPEAKERS SURROUND BACK/BI-AMP/FRONT HIGH/FRONT B terminals to [Front B] by using [Surround Back Speaker Assign] in the [Speaker Settings] menu. Note This setting is not available when headphones are connected. When you press SPEAKERS on the receiver, the [Bluetooth Mode] changes to [Receiver] automatically. [46] Preparation Performing Auto Calibration 5. Performing Auto Calibration You can perform automatic calibration from your listening position. 1 Select [Setup] - [Speaker Settings] from the home menu. 2 Select [Auto Calibration]. 3 Follow the instructions on the TV screen, then press to select [Start]. The measurement starts in 5 seconds. The measurement process will take approximately 30 seconds with a test tone. When the measurement ends, a beep sounds and the screen switches. 4 Select the item you want. Save: Saves the measurement results and exits the setting process. Retry: Performs the Auto Calibration again. Discard: Exits the setting process without saving the measurement results. For details on the measurement results, see "6. Checking Auto Calibration results." 5 Save the measurement results. Select [Save] in step 4. Note If the measurement fails, follow the message, then select [Retry]. For details on the error code and warning message, see "List of messages after Auto Calibration measurements." This setting is not available when headphones are connected. Hint The Auto Calibration function will be canceled if you perform the following during the measurement process: Press . Press the input buttons on the remote control or turn INPUT SELECTOR on the receiver. Press HOME, AMP MENU or on the remote control. Press SPEAKERS on the receiver. Change the volume level. Connect headphones.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
SPA+B
(*)
:
Speakers connected to both the SPEAKERS FRONT A and SPEAKERS SURROUND
BACK/BI-AMP/FRONT HIGH/FRONT B terminals (parallel connection).
(None):
[SPK OFF] appears on the display panel. No audio signals are output from any speaker
terminals.
Note
This setting is not available when headphones are connected.
When you press SPEAKERS on the receiver, the [Bluetooth Mode] changes to [Receiver]
automatically.
[46] Preparation
Performing Auto Calibration
5. Performing Auto Calibration
You can perform automatic calibration from your listening position.
Note
If the measurement fails, follow the message, then select [Retry]. For details on the error code and
warning message, see “List of messages after Auto Calibration measurements
.”
This setting is not available when headphones are connected.
Hint
The Auto Calibration function will be canceled if you perform the following during the measurement
process:
Press
.
Press the input buttons on the remote control or turn INPUT SELECTOR on the receiver.
Press HOME, AMP MENU or
on the remote control.
Press SPEAKERS on the receiver.
Change the volume level.
Connect headphones.
To select [SPB] or [SPA+B], set the assignment for the SPEAKERS SURROUND BACK/BI-AMP/FRONT
HIGH/FRONT B terminals to [Front B] by using [Surround Back Speaker Assign] in the [Speaker Settings] menu.
*
Select [Setup] - [Speaker Settings] from the home menu.
1
Select [Auto Calibration].
2
Follow the instructions on the TV screen, then press
to select [Start].
The measurement starts in 5 seconds.
The measurement process will take approximately 30 seconds with a test tone.
When the measurement ends, a beep sounds and the screen switches.
3
Select the item you want.
Save:
Saves the measurement results and exits the setting process.
Retry:
Performs the Auto Calibration again.
Discard:
Exits the setting process without saving the measurement results.
For details on the measurement results, see “6. Checking
Auto Calibration
results
.”
4
Save the measurement results.
Select [Save] in step 4.
5