ZyXEL NBG6716 User Guide - Page 162

Remote Management and NAT, System Timeout

Page 162 highlights

Chapter 20 Remote Management 20.3.1 Remote Management and NAT When NAT is enabled: • Use the NBG6716's WAN IP address when configuring from the WAN. • Use the NBG6716's LAN IP address when configuring from the LAN. 20.3.2 System Timeout There is a default system management idle timeout of five minutes (three hundred seconds). The NBG6716 automatically logs you out if the management session remains idle for longer than this timeout period. The management session does not time out when a statistics screen is polling. You can change the timeout period in the Maintenance > General screen 20.4 WWW Screen To change your NBG6716's remote management settings, click Management > Remote MGMT > WWW. Figure 100 Management > Remote Management > WWW The following table describes the labels in this screen. Table 61 Management > Remote Management > WWW LABEL DESCRIPTION Port You may change the server port number for a service if needed, however you must use the same port number in order to use that service for remote management. Access Status Select the interface(s) through which a computer may access the NBG6716 using this service. Secured Client IP Address Select All to allow all computes to access the NBG6716. Otherwise, check Selected and specify the IP address of the computer that can access the NBG6716. Apply Click Apply to save your customized settings. Cancel Click Cancel to begin configuring this screen afresh. 162 NBG6716 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250

Chapter 20 Remote Management
NBG6716 User’s Guide
162
20.3.1
Remote Management and NAT
When NAT is enabled:
Use the NBG6716’s WAN IP address when configuring from the WAN.
Use the NBG6716’s LAN IP address when configuring from the LAN.
20.3.2
System Timeout
There is a default system management idle timeout of five minutes (three hundred seconds). The
NBG6716 automatically logs you out if the management session remains idle for longer than this
timeout period. The management session does not time out when a statistics screen is polling. You
can change the timeout period in the
Maintenance > General
screen
20.4
WWW Screen
To change your NBG6716’s remote management settings, click
Management > Remote MGMT >
WWW
.
Figure 100
Management > Remote Management > WWW
The following table describes the labels in this screen.
Table 61
Management > Remote Management > WWW
LABEL
DESCRIPTION
Port
You may change the server port number for a service if needed, however you must
use the same port number in order to use that service for remote management.
Access Status
Select the interface(s) through which a computer may access the NBG6716 using
this service.
Secured Client IP
Address
Select
All
to allow all computes to access the NBG6716.
Otherwise, check
Selected
and specify the IP address of the computer that can
access the NBG6716.
Apply
Click
Apply
to save your customized settings.
Cancel
Click
Cancel
to begin configuring this screen afresh.