ZyXEL NBG6716 User Guide - Page 18

Power

Page 18 highlights

Chapter 1 Introduction 1 Make sure the power LED is on (not blinking). 2 Press the WPS button for more than three seconds and release it. Press the WPS button on another WPS-enabled device within range of the NBG6716. Note: You must activate WPS in the NBG6716 and in another wireless device within two minutes of each other. For more information on using WPS, see Section 8.2 on page 65. 1.7 LEDs Look at the LED lights on the front panel to determine the status of the NBG6716. Use the LED button at the side panel of the device to turn the LED lights on or off. If you have already pushed the LED button to the ON position but none of the LEDS are on, make sure the NBG6716 is receiving power and the power is turned on. Note: The Power LED will be on even if you push the LED button to the OFF position. This is for you to determine whether the NBG6716 is powered on. Figure 3 LED Button LED button 18 NBG6716 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250

Chapter 1 Introduction
NBG6716 User’s Guide
18
1
Make sure the power LED is on (not blinking).
2
Press the WPS
button for more than three seconds and release it. Press the WPS button on another
WPS-enabled device within range of the NBG6716.
Note: You must activate WPS in the NBG6716 and in another wireless device within two
minutes of each other.
For more information on using WPS, see
Section 8.2 on page 65
.
1.7
LEDs
Look at the LED lights on the front panel to determine the status of the NBG6716. Use the
LED
button at the side panel of the device to turn the LED lights on or off. If you have already pushed
the
LED
button to the
ON
position but none of the LEDS are on, make sure the NBG6716 is
receiving power and the power is turned on.
Note: The
Power
LED will be on even if you push the
LED
button to the
OFF
position.
This is for you to determine whether the NBG6716 is powered on.
Figure 3
LED Button
LED button