Home » Cisco Manuals » Bridges & Routers » Cisco 3825 » Manual Viewer

Cisco 3825 Software Configuration Guide - Page 68

Configuring the Card Type for the Cisco 2-port T1/E1-RAN, Configuring Network Clocking Support

UPC - 746320981505

Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Configuration Sequence Chapter 4 Configuring the Cisco 3825 Mobile Wireless Edge Router in a RAN-O Solution with the Command-Line • Configuring Network Clocking Support, page 4-14 • Configuring Multilink Backhaul Interface, page 4-15 • Configuring the PPP Backhaul Interfaces, page 4-19 Configuring the Card Type for the Cisco 2-port T1/E1-RAN Use the following instructions to perform a basic Card Type configuration: enabling the router, enabling an interface, and specifying the card type. You might also need to enter other configuration commands, depending on the requirements for your system configuration and the protocols you plan to route on the interface. Note In the following procedure, press the Return key after each step unless otherwise noted. At any time, you can exit the privileged level and return to the user level by entering disable at the Router# prompt. To select and configure a card type for the Cisco 2-port T1/E1-RAN card, follow these steps: Step 1 Step 2 Step 3 Enter the enable mode. Router> enable Enter the password. Password: password You have entered the enable mode when the prompt changes to Router#. Enter the global configuration mode. Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# You have entered the global configuration mode when the prompt changes to Router(config)#. Note To see a list of the configuration commands available to you, enter ? at the prompt or press the Help key while in the configuration mode. Step 4 Set the card type for the Cisco 2-port T1/E1-RAN card. Router(config-if)# card type {e1 | t1} slot subslot Where: • slot-Slot number of the interface. • subslot-Specifies the VWIC/HWIC slot number. For example, the following command configures the Cisco 2-port T1/E1-RAN card in the Cisco 3825 router slot 0, VWIC/HWIC slot 0 as an E1: Router(config)# card type e1 0 0 When the command is used for the first time, the configuration takes effect immediately. A subsequent change in the card type will not take effect unless you enter the reload command or reboot the router. 4-10 Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide OL-15667-03

Section	Page
Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide	1
Contents	3
Preface	7
Overview of the Cisco 3825 Mobile Wireless Edge Router	11
Introduction	11
RAN-Optimization Implementation	12
Cisco Abis and Iub Optimization over IP Implementation	12
Cisco GSM Abis Optimization over IP	13
Cisco Pseudowire Emulation Edge-to-Edge (PWE3)	14
Cisco Iub Optimization over IP	15
Intelligent Cell Site IP Services	15
Cell Site Points-of-Presence (POPs)	15
Cisco IOS Software Features	16
Software features for the RAN-O Implementation	16
Software Features	17
Redundancy Support	17
HSRP	17
Configuration Statements for CISCO-IP-RAN-BACKHAUL-MIB	18
MIB Support	20
Limitations and Restrictions	21
RAN-O Implementation Limitations and Restrictions	22
Hardware not Supported on the Cisco 3825 Router	22
UMTS Iub and GSM Abis Implementation Limitations and Restrictions	22
Hardware not Supported for UMTS Iub	22
Hardware not Supported for GSM Abis	22
New Features in Cisco IOS Release 12.4(16)MR2	23
Keyword ignore-vpi-vci Added to xconnect Command	23
New Features in Cisco IOS Release 12.4(16)MR1	23
Emulation of TDM Circuit via MPLS/IP (PWE3/TDM)	24
Structure-agnostic TDM over Packet (SAToP)	26
Structure-aware TDM CESoPSN	26
Transportation of ATM Service via MPLS/IP (PWE3/ATM)	27
Transparent Cell Transport Service/ATM Port Mode	27
ATM N-to-One VCC Cell Mode	27
ATM AAL5 CPCS-SDU Mode	28
ATM One-to-One VCC Cell Mode	28
Cell Packing	29
PVC Mapping	29
Transportation of ATM Service via L2TPv3	30
ATM Port Cell Relay Service	30
ATM VCC Cell Relay Service	30
ATM AAL5-SDU Mode	31
Cell Packing	31
PVC Mapping	32
Asymmetric PWE3	32
Ethernet over MPLS	33
VLAN Mode	33
Port Mode	33
PWE3 over MLPPP	34
PWE3 Redundancy	34
TDM PWE3 Redundancy	35
ATM PWE3 Redundancy	35
Ethernet PWE3 Redundancy	35
Maximum Number of Supported ATM Ports	36
ATM Cell Switching	36
New Features in Cisco IOS Release 12.4(16)MR	37
GSMmux-Global System for Mobile Communication (GSM) Abis Optimization over IP	37
UMTSmux-Universal Mobile Telecommunication System (UMTS) Iub Optimization over IP	37
UMTS Congestion Management Control	38
Inverse Multiplexing over ATM (IMA)	39
Permanent Virtual Circuit (PVC) Routing	40
Behavior Changes	42
UMTS QoS	43
Cisco IOS Software Basics	47
Getting Help	47
Understanding Command Modes	48
Undoing a Command or Feature	49
Saving Configuration Changes	49
Where to Go Next	49
First-Time Configuration	51
Understanding Boot Images	51
Understanding the Cisco 3825 Router Interface Numbering	51
Slot and Port Numbering	52
Setup Command Facility	53
Before Starting Your Router	53
Using the Setup Command Facility	54
Configuring Global Parameters	54
Completing the Configuration	57
Configuring the Cisco 3825 Mobile Wireless Edge Router in a RAN-O Solution with the Command-Line Interface	59
Before You Begin	60
Verifying the Version of Cisco IOS Software	60
Clocking Requirements for Cisco 3825 Router	60
Clock-Related Commands	61
Network-Clock-Participate Command	61
Network-Clock-Select Command	61
Clock Source Command	62
Example Configurations	63
Show Controller Command	63
Configuration Sequence	64
Summary of Steps	64
Configuring the Hostname and Password	64
Verifying the Hostname and Password	65
Configuring Gigabit Ethernet Interfaces	66
Configuring the GE Interface IP Address	66
Setting the Speed and Duplex Mode	66
Enabling the GE Interface	67
Configuring the Backhaul Links	67
Configuring the Card Type for the Cisco 2-port T1/E1-RAN	68
Configuring E1 Controllers	69
Configuring T1 Controllers	70
Configuring Network Clocking Support	72
Configuring Multilink Backhaul Interface	73
Creating a Multilink Bundle	73
Handling PFC and ACFC	74
Configuring PFC	74
Configuring ACFC	75
Enable Multilink and Identify the Multilink Interface	75
Enable Real-Time Transport Protocol (RTP) Header-Compression	76
Configuring the PPP Backhaul Interfaces	77
Extended Availability Drop and Insert (EADI)	78
Configuring GSM-Abis Links	78
Configuring UMTS Links	82
Configuring Redundancy	86
Redundant Cisco 3825 Routers	86
Standalone Cisco 3825 Router	91
Configuring for SNMP Support	91
Configuring Inverse Multiplexing over ATM (IMA)	95
Configuring PVC Routing (HSDPA Offload)	99
Configuring UMTS QoS	104
Creating a Class Map	105
Creating a Policy Map	105
Specify the Location of the Interface	106
Assigning a QoS Boilerplate to an Interface	109
Configuring UMTS Congestion Management Control	113
Configuring Satellite Support	116
Configuring Graceful Degradation	117
Saving Configuration Changes	119
Example Configurations	119
BTS/Node-B Configuration	119
BSC/RNC Configuration	123
Monitoring and Managing the Cisco 3825 Router	127
Enabling the Cisco 3825 Router for Remote Network Management	127
Show Commands for Monitoring the Cisco 3825 Router	129
Where to Go Next	131
Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference	133
Configuration Examples	269
Overview	269
Asymmetric PWE3 Configuration	270
Ethernet over MPLS-VLAN and Port Mode Configuration	283
PWE3 over MLPPP Configuration	289
PWE3 Redundancy Configuration	298
TDM over MPLS Configuration	304
ATM over MPLS Configurations	309
ATM over L2TPv3 Configuration	316
GSM Only Configuration	323
UMTS Only Configuration without IMA	327
Combined GSM and UMTS Configuration	331
GSM and UMTS with IMA Configuration	336
GSM and UMTS with IMA and PVC Routing (HSDPA Offload) Configuration	342
GSM Only Configuration via Satellite	348
GSM Congestion Management	351
UMTS Congestion Management	352

Match case Limit results 1 per page

4-10

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Chapter 4

Configuring the Cisco 3825 Mobile Wireless Edge Router in a RAN-O Solution with the Command-Line

Configuration Sequence

•

Configuring Network Clocking Support, page 4-14

•

Configuring Multilink Backhaul Interface, page 4-15

•

Configuring the PPP Backhaul Interfaces, page 4-19

Configuring the Card Type for the Cisco 2-port T1/E1-RAN

Use the following instructions to perform a basic Card Type configuration: enabling the router, enabling

an interface, and specifying the card type. You might also need to enter other configuration commands,

depending on the requirements for your system configuration and the protocols you plan to route on the

interface.

Note

In the following procedure, press the

Return

key after each step unless otherwise noted. At any time,

you can exit the privileged level and return to the user level by entering

disable

at the

Router#

prompt.

To select and configure a card type for the Cisco 2-port T1/E1-RAN card, follow these steps:

Step 1

Enter the enable mode.

Router>

enable

Step 2

Enter the password.

Password:

password

You have entered the enable mode when the prompt changes to

Router#

Step 3

Enter the global configuration mode.

Router#

configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#

You have entered the global configuration mode when the prompt changes to

Router(config)#

Note

To see a list of the configuration commands available to you, enter

at the prompt or press the

Help

key while in the configuration mode.

Step 4

Set the card type for the Cisco 2-port T1/E1-RAN card.

Router(config-if)#

card type {e1 | t1}

slot subslot

Where:

•

slot

—Slot number of the interface.

•

subslot

—Specifies the VWIC/HWIC slot number.

For example, the following command configures the Cisco 2-port T1/E1-RAN card in the Cisco 3825

router slot 0, VWIC/HWIC slot 0 as an E1:

Router(config)#

card type e1 0 0

When the command is used for the first time, the configuration takes effect immediately. A subsequent

change in the card type will not take effect unless you enter the

reload

command or reboot the router.