Cisco SPA112 Administration Guide - Page 61

Firmware Upgrade, Upgrade Error Retry

Get Cisco SPA112 PDF manuals and user guides View all Cisco SPA112 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Configuring Voice Configuring Voice Settings 4 Field Report Rule Firmware Upgrade Description The target URL to which configuration reports are sent. This parameter has the same syntax as the Profile_Rule parameter, and resolves to a TCP/IP command with an associated URL. A configuration report is generated in response to an authenticated SIP NOTIFY message, with Event: report. The report is an XML file containing the name and value of all the device parameters. This parameter may optionally contain an encryption key. For example: [ --key $K ] tftp://ps.callhome.net/$MA/rep.xml.enc Default setting: (empty) Upgrade Enable Enables firmware upgrade operations independently of resync actions. Default setting: Yes Upgrade Error Retry Delay The upgrade retry interval (in seconds) applied in case of upgrade failure. The ATA has a firmware upgrade error timer that activates after a failed firmware upgrade attempt. The timer is initialized with the value in this parameter. The next firmware upgrade attempt occurs when this timer counts down to zero. Default setting: 3600 seconds. Downgrade Rev Limit Enforces a lower limit on the acceptable version number during a firmware upgrade or downgrade. The ATA does not complete a firmware upgrade operation unless the firmware version is greater than or equal to this parameter. Default setting: (empty) Upgrade Rule This parameter is a firmware upgrade script with the same syntax as Profile_Rule. Defines upgrade conditions and associated firmware URLs. Default setting: (empty) Cisco SPA100 Series Phone Adapters Administration Guide 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Configuring Voice
Configuring Voice Settings
Cisco SPA100 Series Phone Adapters Administration Guide
61
4
Firmware Upgrade
Report Rule
The target URL to which configuration reports are sent.
This parameter has the same syntax as the Profile_Rule
parameter, and resolves to a TCP/IP command with an
associated URL.
A configuration report is generated in response to an
authenticated SIP NOTIFY message, with Event: report.
The report is an XML file containing the name and value
of all the device parameters.
This parameter may optionally contain an encryption
key.
For example:
Default setting: (empty)
Upgrade Enable
Enables firmware upgrade operations independently of
resync actions. Default setting: Yes
Upgrade Error Retry
Delay
The upgrade retry interval (in seconds) applied in case
of upgrade failure. The ATA has a firmware upgrade
error timer that activates after a failed firmware upgrade
attempt. The timer is initialized with the value in this
parameter. The next firmware upgrade attempt occurs
when this timer counts down to zero. Default setting:
3600 seconds.
Downgrade Rev
Limit
Enforces a lower limit on the acceptable version number
during a firmware upgrade or downgrade. The ATA does
not complete a firmware upgrade operation unless the
firmware version is greater than or equal to this
parameter. Default setting:
(empty)
Upgrade Rule
This parameter is a firmware upgrade script with the
same syntax as Profile_Rule. Defines upgrade
conditions and associated firmware URLs. Default
setting:
(empty)
Field
Description