Cisco SPA112 Administration Guide - Page 94

For the Refer Target Bye Delay, enter the, Proxy or Outbound Proxy if Use Outbound Proxy

Get Cisco SPA112 PDF manuals and user guides View all Cisco SPA112 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Configuring Voice Configuring Voice Settings 4 Field RTP Log Intvl Restrict Source IP Referor Bye Delay Refer Target Bye Delay Referee Bye Delay Refer-To Target Contact Sticky 183 Auth INVITE Description The interval for the RTP log. Default setting: 0. If Lines 1 and 2 use the same SIP Port value and the Restrict Source IP feature is enabled, the proxy IP address for Lines 1 and 2 is treated as an acceptable IP address for both lines. To enable the Restrict Source IP feature, select yes. Otherwise, select no. If configured, the ATA will drop all packets sent to its SIP Ports originated from an untrusted IP address. A source IP address is untrusted if it does not match any of the IP addresses resolved from the configured Proxy (or Outbound Proxy if Use Outbound Proxy is yes) Default setting: no. Controls when the ATA sends BYE to terminate stale call legs upon completion of call transfers. Multiple delay settings (Referor, Refer Target, Referee, and Refer-To Target) are configured on this screen. For the Referor Bye Delay, enter the appropriate period of time in seconds. Default setting: 4. For the Refer Target Bye Delay, enter the appropriate period of time in seconds. Default setting: 0. For the Referee Bye Delay, enter the appropriate period of time in seconds. Default setting: 0. To contact the refer-to target, select yes. Otherwise, select no. Default setting: no. If this feature is enabled, the ATA ignores further 180 SIP responses after receiving the first 183 SIP response for an outbound INVITE. To enable this feature, select yes. Otherwise, select no. Default setting: no. When enabled, authorization is required for initial incoming INVITE requests from the SIP proxy. Cisco SPA100 Series Phone Adapters Administration Guide 94

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Configuring Voice
Configuring Voice Settings
Cisco SPA100 Series Phone Adapters Administration Guide
94
4
RTP Log Intvl
The interval for the RTP log. Default setting: 0.
Restrict Source IP
If Lines 1 and 2 use the same SIP Port value and
the Restrict Source IP feature is enabled, the
proxy IP address for Lines 1 and 2 is treated as
an acceptable IP address for both lines. To
enable the Restrict Source IP feature, select yes.
Otherwise, select no. If configured, the ATA will
drop all packets sent to its SIP Ports originated
from an untrusted IP address. A source IP
address is untrusted if it does not match any of
the IP addresses resolved from the configured
Proxy (or Outbound Proxy if Use Outbound Proxy
is yes) Default setting: no.
Referor Bye Delay
Controls when the ATA sends BYE to terminate
stale call legs upon completion of call transfers.
Multiple delay settings (Referor, Refer Target,
Referee, and Refer-To Target) are configured on
this screen. For the Referor Bye Delay, enter the
appropriate period of time in seconds. Default
setting: 4.
Refer Target Bye Delay
For the Refer Target Bye Delay, enter the
appropriate period of time in seconds. Default
setting: 0.
Referee Bye Delay
For the Referee Bye Delay, enter the appropriate
period of time in seconds. Default setting: 0.
Refer-To Target Contact
To contact the refer-to target, select yes.
Otherwise, select no. Default setting: no.
Sticky 183
If this feature is enabled, the ATA ignores further
180 SIP responses after receiving the first 183
SIP response for an outbound INVITE. To enable
this feature, select yes. Otherwise, select no.
Default setting: no.
Auth INVITE
When enabled, authorization is required for initial
incoming INVITE requests from the SIP proxy.
Field
Description