Dell PowerVault 56F Dell PowerVault 51F 8-Port Fibre Channel Switch Insta - Page 140

Error Messages by Firmware Module, A-1., errShow Command Example, Table A-1., Errors

Get Dell PowerVault 56F PDF manuals and user guides View all Dell PowerVault 56F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 140 highlights

=> errShow Error 02 -------0x103dc470 (tSilkworm): Apr 9 10:41:06 Error SENSOR-FAILED, 3, sensor 7 (Fan 2) is below minim Type to continue, Q to stop: Error 01 -------0x103dc470 (tSilkworm): Apr Error DIAG-TIMEOUT, 1, Port 2 receive timeout. 9 10:40:51 Type to continue, Q to stop: value = 1 = 0x1 Figure A-1. errShow Command Example To display error messages via Telnet: 1. From the prompt, type errShow. 2. To scroll through the error list, type CR. 3. Scroll through the error log (if no errors were encountered, the message No Error appears). Error Messages by Firmware Module Table A-1 shows the error messages organized by module. Table A-1. Errors Module Error Severity Flood INVLSR (3) Explanation An unknown Link State Record has been received from a neighbor switch. Action Check that all paths and routing tables are correct using the commands uPathShow , or uPathAllShow. If the paths are not correct reboot the neighbor switch that sent the wrong data. Check the paths and routes again. If they are still incorrect, reboot the local switch. A-2 Installation and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
A-2
Installation and Troubleshooting Guide
Figure A-1.
errShow Command Example
To display error messages via Telnet:
1.
From the prompt, type
errShow
.
2.
To scroll through the error list, type
CR.
3.
Scroll through the error log (if no errors were encountered, the message
No
Error
appears).
Error Messages by Firmware Module
Table A-1 shows the error messages organized by module.
=> errShow
Error 02
--------
0x103dc470 (tSilkworm): Apr
9 10:41:06
Error SENSOR-FAILED, 3, sensor 7 (Fan 2) is below minim
Type <CR> to continue, Q<CR> to stop:
Error 01
--------
0x103dc470 (tSilkworm): Apr
9 10:40:51
Error DIAG-TIMEOUT, 1,
Port 2 receive timeout.
Type <CR> to continue, Q<CR> to stop:
value = 1 = 0x1
Table A-1.
Errors
Module
Error
Severity
Explanation
Action
Flood
INVLSR (3)
An unknown Link
State Record has
been received
from a neighbor
switch.
Check that all paths and
routing tables are correct
using the commands
uPathShow <domain>
, or
uPathAllShow
.
If the paths are not correct
reboot the neighbor switch
that sent the wrong data.
Check the paths and routes
again. If they are still incor-
rect, reboot the local switch.