Dell PowerVault 56F Dell PowerVault 51F 8-Port Fibre Channel Switch Insta - Page 30

Power Requirements, PowerVault 51F Switch Front View

Get Dell PowerVault 56F PDF manuals and user guides View all Dell PowerVault 56F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

NOTE: Do not block the front or back air vents. The switch must have clear access to ambient air for cooling. Power Requirements Switch power connection is via a switched connector on the switch's front right side, as shown in Figure 1-1. The PowerVault 51F switch power requirements are as follows: • Properly wired, grounded outlet • Input voltage: 90-257 volts alternating current (VAC) • Total power: Up to 110 watts (depending on configuration; see Appendix A, "Specifications" in the User's Guide) • Input line frequency: 50 to 60 hertz (Hz) The switch has an autoranging power supply that automatically accepts voltages within its ranges. power supply 2 (optional) power supply 1 Figure 1-1. PowerVault 51F Switch Front View NOTE: The switch meets International Electronic Commission (IEC) 801-5 surge voltage requirements; however, there is no other provision for surge protection built into the switch's power supplies. An installation should include normal provisions to assure clean power. 1-2 Dell PowerVault 51F 8-Port Fibre Channel Switch Installation and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
1-2
Dell PowerVault 51F 8-Port Fibre Channel Switch Installation and Troubleshooting Guide
NOTE: Do not block the front or back air vents. The switch must have clear access to
ambient air for cooling.
Power Requirements
Switch power connection is via a switched connector on the switch’s front right side,
as shown in Figure 1-1. The PowerVault 51F switch power requirements are as
follows:
•
Properly wired, grounded outlet
•
Input voltage: 90–257 volts alternating current (VAC)
•
Total power: Up to 110 watts (depending on configuration; see Appendix A,
“Specifications” in the
User’s Guide
)
•
Input line frequency: 50 to 60 hertz (Hz)
The switch has an autoranging power supply that automatically accepts voltages
within its ranges.
Figure 1-1.
PowerVault 51F Switch Front View
NOTE: The switch meets International Electronic Commission (IEC) 801-5 surge volt-
age requirements; however, there is no other provision for surge protection built into
the switch’s power supplies. An installation should include normal provisions to
assure clean power.
power supply 1
power supply 2
(optional)