HP 3310 User Guide - Page 96

To load 35 mm slides, appears backward. Gently press down until it snaps into place.

Page 96 highlights

Load originals and load paper To load 35 mm slides Note The HP All-in-One does not support scanning negative film that is mounted as a slide in plastic or cardboard. 1. Raise the lid and remove the Slide and Negative Film holder and the lid backing. Set the lid backing aside where it will not get damaged or dirty. 2. Unfold the holder so that the half with four slide openings is on top. 3. Place the holder on the glass and match the bottom edge with the bottom edge of the glass. Then, match the right tab on the top half of the holder with the right edge of the glass. 4. Place the slide on the holder so that the front of the image faces down and appears backward. Gently press down until it snaps into place. Note The slide must snap into place for the image to scan properly. If the slide does not touch the glass the final scanned image might be blurry. Tip If the slide does not snap into place easily, try rotating it 180 degrees. Some slides have a gap on one side that prevents them from fitting properly. User Guide 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212

To load 35 mm slides
Note
The HP All-in-One does not support scanning negative film that is
mounted as a slide in plastic or cardboard.
1.
Raise the lid and remove the Slide and Negative Film holder and the lid backing.
Set the lid backing aside where it will not get damaged or dirty.
2.
Unfold the holder so that the half with four slide openings is on top.
3.
Place the holder on the glass and match the bottom edge with the bottom edge of
the glass. Then, match the right tab on the top half of the holder with the right
edge of the glass.
4.
Place the slide on the holder so that the front of the image faces down and
appears backward. Gently press down until it snaps into place.
Note
The slide must snap into place for the image to scan properly. If the
slide does not touch the glass the final scanned image might be blurry.
Tip
If the slide does not snap into place easily, try rotating it 180
degrees. Some slides have a gap on one side that prevents them from
fitting properly.
User Guide
93
Load originals and load paper