HP Designjet L26100 HP Designjet L26500/L26100 Printer Series - User's Guide - Page 47

printing you do not need to pull the substrate, If you are loading the take-up reel

Get HP Designjet L26100 PDF manuals and user guides View all HP Designjet L26100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

8. Ensure that both stops are placed on the spindle, but leave some space between the core and the stops at each end. 9. Load the take-up reel spindle into the printer by pushing firmly on both ends of the spindle. 10. Press the OK button on the front panel. Advance the substrate using the arrows on the front panel. Make sure that the substrate passes in front of the loading table, as shown. Handle the substrate 11. Pull down the center of the substrate's leading edge to straighten the substrate. Do not attempt to pull more substrate out of the printer. NOTE: If you are loading the take-up reel during printing you do not need to pull the substrate taut. Tape the substrate to the spindle core when an adequate length of substrate has fed from the printer after printing begins. 12. Adjust the position of the core on the take-up reel spindle so that it is aligned with the substrate. ENWW The take-up reel 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
8.
Ensure that both stops are placed on the spindle, but leave some space between the core and the
stops at each end.
9.
Load the take-up reel spindle into the printer by pushing firmly on both ends of the spindle.
10.
Press the OK button on the front panel.
Advance the substrate using the arrows on the front panel. Make sure that the substrate passes in
front of the loading table, as shown.
11.
Pull down the center of the substrate's leading edge to straighten the substrate. Do
not
attempt to
pull more substrate out of the printer.
NOTE:
If you are loading the take-up reel
during
printing you do not need to pull the substrate
taut. Tape the substrate to the spindle core when an adequate length of substrate has fed from the
printer after printing begins.
12.
Adjust the position of the core on the take-up reel spindle so that it is aligned with the substrate.
ENWW
The take-up reel
43
Handle the substrate