HP Designjet L26100 HP Designjet L26500/L26100 Printer Series - User's Guide - Page 53

The edge holders

Get HP Designjet L26100 PDF manuals and user guides View all HP Designjet L26100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

9. Remove the roll from the printer, pulling out the end on the right side of the printer first. Do not insert your fingers into the spindle supports during the removal process. Handle the substrate 10. To remove the roll from the printer after you have unloaded the take-up reel, see Unload a roll from the printer on page 33. The edge holders The edge holders are designed to prevent the edges of the substrate from rising while printing is in progress. They are recommended for textile and double-sided printing (even if the front panel does not suggest them), and are not normally necessary in other situations. When not in use, they can be stored in their case at the rear of the printer. If you choose to use them, you should place them on the platen when prompted by the front panel (this prompt appears when using the loading accessory). Open the window, place the edge holders, then close the window. WARNING! Do not touch the printer's drying enclosure. Even after you have opened the window latch, which disconnects the power to the drying and curing modules, the internal surfaces could be hot. The edge holders should be placed on the platen so that they slightly overlap the left and right edges of the substrate. The edge holders fit into holes in the platen, and they are magnetic, which helps them to stay in place. Slide the edge holder to the left or right with your fingers so that you can see the edge of the substrate in the two square holes in the side of the edge holder. ENWW The edge holders 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
9.
Remove the roll from the printer, pulling out the end on the right side of the printer first. Do not
insert your fingers into the spindle supports during the removal process.
10.
To remove the roll from the printer after you have unloaded the take-up reel, see
Unload a roll
from the printer
on page
33
.
The edge holders
The edge holders are designed to prevent the edges of the substrate from rising while printing is in
progress. They are recommended for textile and double-sided printing (even if the front panel does not
suggest them), and are not normally necessary in other situations. When not in use, they can be stored
in their case at the rear of the printer.
If you choose to use them, you should place them on the platen when prompted by the front panel (this
prompt appears when using the loading accessory). Open the window, place the edge holders, then
close the window.
WARNING!
Do not touch the printer's drying enclosure. Even after you have opened the window
latch, which disconnects the power to the drying and curing modules, the internal surfaces could be
hot.
The edge holders should be placed on the platen so that they slightly overlap the left and right edges of
the substrate. The edge holders fit into holes in the platen, and they are magnetic, which helps them to
stay in place.
Slide the edge holder to the left or right with your fingers so that you can see the edge of the substrate
in the two square holes in the side of the edge holder.
ENWW
The edge holders
49
Handle the substrate