HP Designjet L26100 HP Designjet L26500/L26100 Printer Series - User's Guide - Page 57

If you are loading transparent substrate without opaque borders, you are asked to enter the width

Get HP Designjet L26100 PDF manuals and user guides View all HP Designjet L26100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

9. Select the type of substrate you are loading. NOTE: You should select the name of the particular substrate that you are using in your RIP software, not in the front panel. TIP: When loading very thin substrates, always select the substrate type as Banner to minimize the vacuum pressure applied while loading; when loading very thick substrates, always select the substrate type as HP Photorealistic to maximize the vacuum pressure. After loading and before printing, go to the front panel and change to the correct type for the substrate you are loading: select the icon, then select View loaded substrate > Change loaded substrate. 10. After passing through the printer, the loading accessory can be removed by hand. Handle the substrate 11. The printer checks the substrate in various ways and may ask you to correct problems with skew or tension. NOTE: You can specify the maximum permitted amount of skew at the front panel: select the icon, then select Substrate handling options > Max skew setting. 12. If you are loading transparent substrate without opaque borders, you are asked to enter the width of the substrate and the distance of the right edge from the printer's side plate (as indicated by the ruler on the front of the curing module). 13. If you have chosen double-sided printing, the front panel may ask a question about it at this point. 14. The printer calibrates the substrate advance. ENWW The loading accessory 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
9.
Select the type of substrate you are loading.
NOTE:
You should select the name of the particular substrate that you are using in your RIP
software, not in the front panel.
TIP:
When loading very thin substrates, always select the substrate type as
Banner
to minimize
the vacuum pressure applied while loading; when loading very thick substrates, always select the
substrate type as
HP Photorealistic
to maximize the vacuum pressure. After loading and before
printing, go to the front panel and change to the correct type for the substrate you are loading:
select the
icon, then select
View loaded substrate
>
Change loaded substrate
.
10.
After passing through the printer, the loading accessory can be removed by hand.
11.
The printer checks the substrate in various ways and may ask you to correct problems with skew or
tension.
NOTE:
You can specify the maximum permitted amount of skew at the front panel: select the
icon, then select
Substrate handling options
>
Max skew setting
.
12.
If you are loading transparent substrate without opaque borders, you are asked to enter the width
of the substrate and the distance of the right edge from the printer's side plate (as indicated by the
ruler on the front of the curing module).
13.
If you have chosen double-sided printing, the front panel may ask a question about it at this point.
14.
The printer calibrates the substrate advance.
ENWW
The loading accessory
53
Handle the substrate