HP Designjet L26100 HP Designjet L26500/L26100 Printer Series - User's Guide - Page 49

The loop-shaper must have end caps. Make sure that the end caps extend over the edges of

Get HP Designjet L26100 PDF manuals and user guides View all HP Designjet L26100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

16. Gently lower the loading table, to avoid wrinkles and improve winding. 17. Assemble a light loop-shaper by matching the shape-coded and color-coded lengths of plastic tubing. The loop-shaper must be the same width as the substrate that you are using. Make sure that both end caps are firmly fitted on the ends of the loop-shaper. NOTE: The front-panel display shows the required length of the loop-shaper based on the width of the roll that you have loaded into the printer. Handle the substrate 18. Carefully insert the light loop-shaper. This is essential: the take-up reel will not function correctly without it. The loop-shaper must have end caps. Make sure that the end caps extend over the edges of the substrate. 19. Move the stops towards the center until they are pressing up against the core on both sides, then lock them. ENWW The take-up reel 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
16.
Gently lower the loading table, to avoid wrinkles and improve winding.
17.
Assemble a light loop-shaper by matching the shape-coded and color-coded lengths of plastic
tubing. The loop-shaper must be the same width as the substrate that you are using. Make sure
that both end caps are firmly fitted on the ends of the loop-shaper.
NOTE:
The front-panel display shows the required length of the loop-shaper based on the width
of the roll that you have loaded into the printer.
18.
Carefully insert the light loop-shaper. This is essential: the take-up reel will not function correctly
without it.
The loop-shaper must have end caps. Make sure that the end caps extend over the edges of the
substrate.
19.
Move the stops towards the center until they are pressing up against the core on both sides, then
lock them.
ENWW
The take-up reel
45
Handle the substrate