HP Designjet L26100 HP Designjet L26500/L26100 Printer Series - User's Guide - Page 6

Heat hazard, Fire hazard, Introduction

Get HP Designjet L26100 PDF manuals and user guides View all HP Designjet L26100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Introduction The printer uses two power cords. Unplug both power cords before servicing the printer. The printer must be connected to earthed mains outlets only. To avoid the risk of electric shock: ● Do not attempt to dismantle the drying and curing modules or the electrical control cabinet. ● Do not remove or open any other closed system covers or plugs. ● Do not insert objects through slots in the printer. ● Test the functionality of the Residual Current Circuit Breaker (RCCB) every 6 months. Heat hazard The drying and curing subsystems of the printer operate at high temperatures and can cause burns if touched. To avoid personal injury, take the following precautions. ● Do not touch the internal enclosures of the printer's drying and curing modules. Even after opening the window latch that disconnects drying and curing power, the internal surfaces could be hot. ● Take special care when accessing the substrate path. Fire hazard The drying and curing subsystems of the printer operate at high temperatures. Call your service representative if the printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) is repeatedly tripped. To avoid the risk of fire, take the following precautions. ● Use the power supply voltage specified on the nameplate. ● Connect the power cords to dedicated lines, each protected by a branch circuit breaker according to the rating of the wall socket. Do not use a power strip (relocatable power tap) to connect both power cords. ● Use only the power cords supplied by HP with the printer. Do not use a damaged power cord. Do not use the power cords with other products. ● Do not insert objects through slots in the printer. ● Take care not to spill liquid on the printer. ● Do not use aerosol products that contain flammable gases inside or around the printer. ● Do not block or cover the openings of the printer. ● Do not attempt to dismantle the drying or curing module, or the electrical control cabinet. ● Ensure that the operating temperature of the substrate loaded recommended by the manufacturer is not exceeded. If this information is not available from the manufacturer, do not load substrates that cannot be used at an operating temperature under 125°C (257°F). ● Do not load substrates with auto-ignition temperatures below 300°C (572°F). See note below. 2 Chapter 1 Introduction ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
The printer uses two power cords. Unplug both power cords before servicing the printer. The printer
must be connected to earthed mains outlets only.
To avoid the risk of electric shock:
●
Do not attempt to dismantle the drying and curing modules or the electrical control cabinet.
●
Do not remove or open any other closed system covers or plugs.
●
Do not insert objects through slots in the printer.
●
Test the functionality of the Residual Current Circuit Breaker (RCCB) every 6 months.
Heat hazard
The drying and curing subsystems of the printer operate at high temperatures and can cause burns if
touched. To avoid personal injury, take the following precautions.
●
Do not touch the internal enclosures of the printer's drying and curing modules. Even after opening
the window latch that disconnects drying and curing power, the internal surfaces could be hot.
●
Take special care when accessing the substrate path.
Fire hazard
The drying and curing subsystems of the printer operate at high temperatures. Call your service
representative if the printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) is
repeatedly tripped.
To avoid the risk of fire, take the following precautions.
●
Use the power supply voltage specified on the nameplate.
●
Connect the power cords to dedicated lines, each protected by a branch circuit breaker according
to the rating of the wall socket. Do not use a power strip (relocatable power tap) to connect both
power cords.
●
Use only the power cords supplied by HP with the printer. Do not use a damaged power cord. Do
not use the power cords with other products.
●
Do not insert objects through slots in the printer.
●
Take care not to spill liquid on the printer.
●
Do not use aerosol products that contain flammable gases inside or around the printer.
●
Do not block or cover the openings of the printer.
●
Do not attempt to dismantle the drying or curing module, or the electrical control cabinet.
●
Ensure that the operating temperature of the substrate loaded recommended by the manufacturer
is not exceeded. If this information is not available from the manufacturer, do not load substrates
that cannot be used at an operating temperature under 125°C (257°F).
●
Do not load substrates with auto-ignition temperatures below 300°C (572°F). See note below.
2
Chapter 1
Introduction
ENWW
Introduction