HP Scitex LX600 HP Scitex LX Printer Family - User's guide - Page 27

Prepare to print

Get HP Scitex LX600 PDF manuals and user guides View all HP Scitex LX600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

● A custom position is used for thick substrates, or for substrates that wrinkle slightly due to heating. TIP: Try to avoid wrinkling by using substrates that do not wrinkle, or by using a slower print mode that will allow you to lower the drying temperature. We recommend setting the custom position to the thickness of the substrate plus two or three millimeters. The current setting is indicated in the front panel by a √ mark. ● The normal position is suitable for unwrinkled substrates up to 0.7 mm (0.03 in) thick. WARNING! Keep away from the printer's moving parts until the carriage beam has reached its new position. NOTE: If you have installed the ink collector kit, the normal position and the lowest custom position are automatically adjusted to take account of that. Prepare to print The following steps that must be followed before the printer can print: 1. Ensure that the ink collector kit is installed for porous substrates, and not installed for non-porous substrates. See The ink collector kit (LX800 only) on page 25. 2. Start the printer. See Turn the printer on and off on page 11. 3. Go to the HP Internal Print Server and select Substrate > Load/Unload to open the Printer Configuration window. ENWW Prepare to print 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
●
A custom position is used for thick substrates, or for substrates that wrinkle slightly due to heating.
TIP:
Try to avoid wrinkling by using substrates that do not wrinkle, or by using a slower print mode
that will allow you to lower the drying temperature.
We recommend setting the custom position to the thickness of the substrate plus two or three
millimeters. The current setting is indicated in the front panel by a
√
mark.
●
The normal position is suitable for unwrinkled substrates up to 0.7 mm (0.03 in) thick.
WARNING!
Keep away from the printer's moving parts until the carriage beam has reached its new
position.
NOTE:
If you have installed the ink collector kit, the normal position and the lowest custom position
are automatically adjusted to take account of that.
Prepare to print
The following steps that must be followed before the printer can print:
1.
Ensure that the ink collector kit is installed for porous substrates, and not installed for non-porous
substrates. See
The ink collector kit (LX800 only)
on page
25
.
2.
Start the printer. See
Turn the printer on and off
on page
11
.
3.
Go to the HP Internal Print Server and select
Substrate
>
Load/Unload
to open the Printer
Configuration window.
ENWW
Prepare to print
23