HP Scitex LX600 HP Scitex LX Printer Family - User's guide - Page 51

to unroll some more. The substrate, from the front panel's Substrate menu

Get HP Scitex LX600 PDF manuals and user guides View all HP Scitex LX600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

10. Close the latches to secure the spindle in place. TIP: If you cannot close the gear side latch, try sliding the spindle towards the side plate to make sure the end flange is not sitting on the bearings. 11. In the same way, load the spindle with the empty cores into the front of the printer. In this case, the geared end of the spindle should be on the right. 12. Check that the printer has finished raising the carriage beam. 13. Pass the leading edges of both rolls through the printer to the output spindle. TIP: Two people are recommended for this operation (one per roll). 14. Once in front of the printer, if you find that you haven't unrolled enough substrate, select Start main roller motion from the front panel's Substrate menu to unroll some more. The substrate unrolls only when you pull it. 15. Before taping the leading edges of the two substrate rolls to the empty cores on the output spindle, check by measurement that they are in the same positions on the output spindle as on the input spindle. ENWW Load a roll into the printer 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
10.
Close the latches to secure the spindle in place.
TIP:
If you cannot close the gear side latch, try sliding the spindle towards the side plate to make
sure the end flange is not sitting on the bearings.
11.
In the same way, load the spindle with the empty cores into the front of the printer. In this case, the
geared end of the spindle should be on the right.
12.
Check that the printer has finished raising the carriage beam.
13.
Pass the leading edges of both rolls through the printer to the output spindle.
TIP:
Two people are recommended for this operation (one per roll).
14.
Once in front of the printer, if you find that you haven't unrolled enough substrate, select
Start main
roller motion
from the front panel's Substrate menu
to unroll some more. The substrate
unrolls only when you pull it.
15.
Before taping the leading edges of the two substrate rolls to the empty cores on the output spindle,
check by measurement that they are in the same positions on the output spindle as on the input
spindle.
ENWW
Load a roll into the printer
47