HP Scitex LX600 HP Scitex LX Printer Family - User's guide - Page 29

Removal and replacement, The ink collector kit (LX800 only)

Get HP Scitex LX600 PDF manuals and user guides View all HP Scitex LX600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

The correct position is illustrated below, where (1) indicates the edge of the substrate. The substrate should be free to move, and should not touch the ends of the edge holder. CAUTION: Wrongly positioned edge holders could severely damage the printheads and carriage. Removal and replacement When the printer is delivered, the left and right edge holders are already installed on the print platen, and there is no need to remove them. When they are not being used they can be pushed to the side. However, the central edge holders used for dual-roll printing must be removed for single-roll printing. To install an edge holder, stand at the front of the printer and attach the rear of the edge holder to the rear of the platen, then pull the front of the edge holder towards you and attach it to the front of the platen. CAUTION: Do not bend the edge holder. It should remain perfectly straight, otherwise it could damage the printheads and carriage. The ink collector kit (LX800 only) Before printing on porous substrates, such as textile or mesh substrates, you must install the ink collector kit provided with your printer, to protect the printer from the ink that falls through the substrate. The kit must be removed before printing on non-porous substrates. ENWW The ink collector kit (LX800 only) 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
The correct position is illustrated below, where (1) indicates the edge of the substrate. The substrate
should be free to move, and should not touch the ends of the edge holder.
CAUTION:
Wrongly positioned edge holders could severely damage the printheads and carriage.
Removal and replacement
When the printer is delivered, the left and right edge holders are already installed on the print platen,
and there is no need to remove them. When they are not being used they can be pushed to the side.
However, the central edge holders used for dual-roll printing must be removed for single-roll printing.
To install an edge holder, stand at the front of the printer and attach the rear of the edge holder to the
rear of the platen, then pull the front of the edge holder towards you and attach it to the front of the
platen.
CAUTION:
Do not bend the edge holder. It should remain perfectly straight, otherwise it could damage
the printheads and carriage.
The ink collector kit (LX800 only)
Before printing on porous substrates, such as textile or mesh substrates, you must install the ink collector
kit provided with your printer, to protect the printer from the ink that falls through the substrate. The kit
must be removed before printing on non-porous substrates.
ENWW
The ink collector kit (LX800 only)
25