HP Scitex LX600 HP Scitex LX Printer Family - User's guide - Page 52

WARNING, distance for thick substrates or substrates that may wrinkle in the print zone

Get HP Scitex LX600 PDF manuals and user guides View all HP Scitex LX600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

16. Tape the leading edges of both rolls to the empty cores on the output spindle. 17. Install the four edge holders. See The substrate edge holders on page 24. 18. Unlock the differentials on the input and output spindles. 19. Go to the front panel and select Carriage beam position > Move to printing (normal) to lower the carriage beam into its normal position, close to the substrate. This process takes about 2 minutes to complete. NOTE: The Move to printing (custom) position allows you to set the printhead-to-substrate distance for thick substrates or substrates that may wrinkle in the print zone, to avoid ink smearing. Be aware that raising the printhead from the substrate may give poorer print quality. WARNING! Do not insert your hands or anything else into the printer while the carriage beam is descending. 48 Chapter 3 Handle the substrate ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
16.
Tape the leading edges of both rolls to the empty cores on the output spindle.
17.
Install the four edge holders. See
The substrate edge holders
on page
24
.
18.
Unlock the differentials on the input and output spindles.
19.
Go to the front panel and select
Carriage beam position
>
Move to printing (normal)
to lower
the carriage beam into its normal position, close to the substrate. This process takes about 2
minutes to complete.
NOTE:
The
Move to printing (custom)
position allows you to set the printhead-to-substrate
distance for thick substrates or substrates that may wrinkle in the print zone, to avoid ink smearing.
Be aware that raising the printhead from the substrate may give poorer print quality.
WARNING!
Do not insert your hands or anything else into the printer while the carriage beam is
descending.
48
Chapter 3
Handle the substrate
ENWW