HP Scitex LX600 HP Scitex LX Printer Family - User's guide - Page 55

Close the latches to secure the spindle in place., into the printer.

Get HP Scitex LX600 PDF manuals and user guides View all HP Scitex LX600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

4. Go to the front panel and select Carriage beam position > Move to highest position. The printer raises the carriage beam, making it easy to insert the substrate. This process takes about 2 minutes to complete. During this period, you can load the input roll. NOTE: While the carriage beam is rising, you can stop it by pressing the Cancel key. 5. Bring the new roll on its spindle to the rear of the printer, with the geared end of the spindle on the left. 6. Rest the ends of the spindle on the platforms provided at the rear of the printer; plastic pads are provided to absorb the impacts. 7. Open the latches at both ends of the spindle (if they were closed) and push the roll on its spindle into the printer. 8. Close the latches to secure the spindle in place. TIP: If you cannot close the gear side latch, try sliding the spindle towards the side plate to make sure the end flange is not sitting on the bearings. 9. Check that the printer has finished raising the carriage beam. ENWW Load a roll into the printer 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
4.
Go to the front panel and select
Carriage beam position
>
Move to highest position
.
The printer raises the carriage beam, making it easy to insert the substrate. This process takes
about 2 minutes to complete. During this period, you can load the input roll.
NOTE:
While the carriage beam is rising, you can stop it by pressing the
Cancel
key.
5.
Bring the new roll on its spindle to the rear of the printer, with the geared end of the spindle on the
left.
6.
Rest the ends of the spindle on the platforms provided at the rear of the printer; plastic pads are
provided to absorb the impacts.
7.
Open the latches at both ends of the spindle (if they were closed) and push the roll on its spindle
into the printer.
8.
Close the latches to secure the spindle in place.
TIP:
If you cannot close the gear side latch, try sliding the spindle towards the side plate to make
sure the end flange is not sitting on the bearings.
9.
Check that the printer has finished raising the carriage beam.
ENWW
Load a roll into the printer
51