HP Scitex LX600 HP Scitex LX Printer Family - User's guide - Page 59

Load a roll (roll-to-free-fall with collector configuration) (LX800 only)

Page 59 highlights

Load a roll (roll-to-free-fall with collector configuration) (LX800 only) This configuration is similar to the roll-to-free-fall configuration, but with the addition of a collector roller and loop shaper. The following illustration shows a completed configuration with a single roll of porous substrate, so the ink collector kit has been installed. TIP: Do not try to load or unload the collector while printing. Before starting to load the substrate, select a loop shaper of the correct length to match the substrate width. The following tubes are supplied so that you can make up loop shapers of many different lengths. ● One 152-mm (6-in) tube ● Two 203-mm (8-in) tubes ● One 305-mm (12-in) tube ● One 610-mm (24-in) tube ● Two 1067-mm (42-in) tubes ● Two end flanges, to be placed at each end to avoid lateral displacement of the loop shaper during printing For example, you can make up the following loop shapers. ● 914 mm (36 in): 610-mm (24-in) and 305-mm (12-in) tubes ● 1016 mm (40 in): 610-mm (24-in) and two 203-mm (8-in) tubes ● 1270 mm (50 in): 1067-mm (42-in) and 203-mm (8-in) tubes ● 1372 mm (54 in): 1067-mm (42-in) and 305-mm (12-in) tubes ● 1524 mm (60 in): 1067-mm (42-in), 305-mm (12-in) and 152-mm (6-in) tubes ● 1829 mm (72 in): 1067-mm (42-in), 610-mm (24-in) and 152-mm (6-in) tubes ● 1981 mm (78 in): 1067-mm (42-in), 610-mm (24-in) and two 152-mm (6-in) tubes ● 2032 mm (80 in): 1067-mm (42-in), 610-mm (24-in), 203-mm (8-in) and 152-mm (6-in) tubes ENWW Load a roll into the printer 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101

Load a roll (roll-to-free-fall with collector configuration) (LX800 only)
This configuration is similar to the roll-to-free-fall configuration, but with the addition of a collector roller
and loop shaper.
The following illustration shows a completed configuration with a single roll of porous substrate, so the
ink collector kit has been installed.
TIP:
Do not try to load or unload the collector while printing.
Before starting to load the substrate, select a loop shaper of the correct length to match the substrate
width. The following tubes are supplied so that you can make up loop shapers of many different lengths.
One 152-mm (6-in) tube
Two 203-mm (8-in) tubes
One 305-mm (12-in) tube
One 610-mm (24-in) tube
Two 1067-mm (42-in) tubes
Two end flanges, to be placed at each end to avoid lateral displacement of the loop shaper during
printing
For example, you can make up the following loop shapers.
914 mm (36 in): 610-mm (24-in) and 305-mm (12-in) tubes
1016 mm (40 in): 610-mm (24-in) and two 203-mm (8-in) tubes
1270 mm (50 in): 1067-mm (42-in) and 203-mm (8-in) tubes
1372 mm (54 in): 1067-mm (42-in) and 305-mm (12-in) tubes
1524 mm (60 in): 1067-mm (42-in), 305-mm (12-in) and 152-mm (6-in) tubes
1829 mm (72 in): 1067-mm (42-in), 610-mm (24-in) and 152-mm (6-in) tubes
1981 mm (78 in): 1067-mm (42-in), 610-mm (24-in) and two 152-mm (6-in) tubes
2032 mm (80 in): 1067-mm (42-in), 610-mm (24-in), 203-mm (8-in) and 152-mm (6-in) tubes
ENWW
Load a roll into the printer
55